Abstract:Laser Powder Bed Fusion (L-PBF) provides a larger design freedom than conventional manufacturing techniques. Surface post-processing is widely investigated to improve the roughness of as built L-PBF parts by reducing powder sintered to the surface and the staircase effect, but it becomes even more important to guarantee a smooth surface if support structures are included for tilted overhanging structures. This study focuses on L-PBF AlSi10Mg samples with a building angle of 30° with respect to the baseplate. This building angle inevitably requires support structures. The study investigates if a hybrid surface treatment combining chemical and electrochemical polishing, called Hirtisation®, removes the support structure and to what extent it improves the surface roughness of samples with a 30° building angle. Currently, the results of surface treatments are mostly reported on vertically built samples while down-facing areas of samples with a lower building angle are typically the roughest areas of the samples causing crack initiation in fatigue. Roughness, defect population, residual stresses, microstructure, fatigue, and tensile properties are studied to investigate correlations with the physical effect of Hirtisation. A porous zone is observed in the down-facing area close to the support structures of as built samples. Hirtisation removed successfully the support and the porous area. In the down-facing roughest area, the average values of the average roughness, mean roughness depth and deepest valley depth are reduced by respectively 56,5%, 58,7% and 51,5% by Hirtisation compared to the as built state. The deepest valley measured reduced from 155,5 μm to 74,4 μm. Hirtisation combined with annealing increased the fatigue resistance at a stress amplitude of 120 MPa with a factor 3,1 compared to the as built state and with a factor 2,7 compared to the annealing state. The improved fatigue resistance is linked to halving the deepest valley depth as well as a change in the residual stress at the outer surface from tensile stresses after annealing to a small compressive stress after Hirtisation which counteracts the tensile load in fatigue. Hence, Hirtisation reduces roughness, inverses a tensile residual stress at the outer surface to a small compressive residual stress. In addition, the chemical-electrochemical process allows to access areas which are impossible to post-process with e.g. sandblasting or vibratory polishing. These conclusions make Hirtisation interesting for further investigations for future applications, however the deepest valley depth could be reduced more by increasing the material removal in the process to improve the fatigue life more.

Effect of Hirtisation treatment on surface quality and mechanical properties of AlSi10Mg samples produced by laser powder bed fusion

Tailoring heat treatment for AlSi7Mg0.6 parts with as-built surface generated by laser powder bed fusion to reduce surface roughness sensitivity

Influence of microstructure and surface topography on material removal by the Hirtisation® process

Effect of hirtisation on the roughness and fatigue performance of porous titanium lattice structures

Influence of Laser Polishing on the Material Properties of Aluminium L-PBF Components

Improving Surface Electrochemical Polishing Quality of Additive Manufactured AlSi10Mg by Reconstituting the Si Phase

In Situ Ageing with the Platform Preheating of AlSi10Mg Alloy Manufactured by Laser Powder-Bed Fusion Process

Optimisation of the laser polishing for laser-powder bed fusion and electron beam-powder bed fusion Ti6Al4V surfaces

Effect of Build Orientation and Heat Treatment on Erosion Behavior of Al10SiMg Fabricated Using Laser Powder Bed Fusion

Additive Manufacturing of AlSi10Mg and Ti6Al4V Lightweight Alloys via Laser Powder Bed Fusion: A Review of Heat Treatments Effects

Surface Treatment of Powder-Bed Fusion Additive Manufactured Metals for Improved Fatigue Life

Influences of Surface, Heat Treatment, and Print Orientation on the Anisotropy of the Mechanical Properties and the Impact Strength of Ti 6Al 4V Processed by Laser Powder Bed Fusion

Mechanical Properties of AlSi10Mg Processed by Laser Powder Bed Fusion at Elevated Temperature

The mechanism behind the effect of building orientation and surface roughness on hydrogen embrittlement of laser powder bed fused Ti-6Al-4V

Surface condition driven fatigue performance of laser powder bed fusion H13 steel

Microstructural analysis of the influences of platform preheating and post-build heat treatment on mechanical properties of laser powder bed fusion manufactured AlSi10Mg alloy

In-Situ Laser Polishing Additive Manufactured AlSi10Mg: Effect of Laser Polishing Strategy on Surface Morphology, Roughness and Microhardness

Fatigue crack nucleation and growth in laser powder bed fusion AlSi10Mg under as built and post-treated conditions

Innovative Post-Processing for Complex Geometries and Inner Parts of 3D-Printed AlSi10Mg Devices

Processing of High Interstitial Austenitic Steel with PBF‐LB/M‐Evolution of chemical inhomogeneity and microstructural features during Post‐Processing

Influence of Contour Scan Variation on Surface, Bulk and Mechanical Properties of LPBF-Processed AlSi7Mg0.6