Abstract:It is suggested that fatigue failure mechanisms in the face-centered cubic metals are greatly affected by stacking fault energy. It was from this viewpoint that the fatigue crack initiation and stage I type crack propagation in 18-8 austenitic steel which had the lowest stacking fault energy among the face-centered cubic metals on the market, were discussed by the X-ray microbeam diffraction technique and the replica electron microscopic method.The fatigue slip line at room temperature tests has fine and straight configurations which are characteristic of low stacking fault energy materials, while the wavy and coarse slip line is typical of fatigue tests at 200°C where screw dislocation is more easily prone to cross slip. In both of these cases very complicated deformation configurations are caused by double slip and cross slip near the grain boundaries, and frequent extrusion and intrusion are observed in these areas. Fatigue crack nucleation might be caused by stress concentration at the notch and peak topography. The stage I type fatigue crack propagates immediately after the initiation, mainly along and frequently across the intense slip lines. Its growth in the area neighbouring the grain boundary runs in the direction that depends on both the crystal orientations of the grain containing the crack and the grains adjacent to it.Total misorientation and micro lattice strain measured by X-ray micro-beam diffraction technique increase abruptly at early fatigue stressing, then equilibrium values are attained and finally increase rapidly. These three periods during the fatigue deformation might be corresponding to those of the fine slip line initiation, the intensification of each slip line without new slip line formation and of final initiation of micro crack, respectively. Furthermore it will be noticed that the equilibrium value of total misorientation of 18-8 austenitic steel during the fatigue process is about one-tenth of that of carbon steel.The area of substructural zone near the fatigue crack of 18-8 austenitic steel is smaller than that of aluminum of high stacking fault energy and body-centered cubic iron. Therefore, the formations of subgrain and martensite could not be detected by X-ray micro-beam diffraction technique when irradiated by Cr-Kα of 200μφ beam size. In order to clarify these points the detailed observation at the fatigue crack tip must be made by using transmission electron microscopy. These results will be reported elsewhere.

On the Stacking Fault Energy Evaluation and Deformation Mechanism of Sanicro-28 Super-Austenitic Stainless Steel

Stacking Fault Energy Determination in Fe-Mn-Al-C Austenitic Steels by X-ray Diffraction

Stacking Fault Energy Analyses of Additively Manufactured Stainless Steel 316L and CrCoNi Medium Entropy Alloy Using In Situ Neutron Diffraction

Deformation Microstructure and Deformation-Induced Martensite in Austenitic Fe-Cr-Ni Alloys Depending on Stacking Fault Energy

Stacking fault energy prediction for austenitic steels: thermodynamic modeling vs. machine learning

Microstructural Evolutions under Ultrasonic Treatment in 304 and 316 Austenitic Stainless Steels: Impact of Stacking Fault Energy

In-situ investigation of the interaction between hydrogen and stacking faults in a bulk austenitic steel

Insights into plastic deformation mechanisms of austenitic steels by coupling generalized stacking fault energy and semi-discrete variational Peierls-Nabarro model

Thermal deformation behavior and microstructure analysis of the as-cast super austenitic stainless steel Sanicro35

XRD measurement of stacking fault energy of Cr–Ni austenitic steels: influence of temperature and alloying elements

Can experiment determine the stacking fault energy of metastable alloys?

Microscopic Observations of Fatigue Crack Initiation Process in 18-8 Austenitic Steel

Correlation of stacking fault energy with deformation mechanism in Cu–(2, 20)Zn alloys

Unveiling the relationship between dislocation structure evolution and strain hardening behavior of S32654 super-austenitic stainless steel

Nitrogen in chromium–manganese stainless steels: a review on the evaluation of stacking fault energy by computational thermodynamics

Effect of Stacking Fault Energy on the Grain Structure Evolution of FCC Metals During Friction Stir Welding

Effects of SMAT Temperature and Stacking Fault Energy on the Mechanical Properties and Microstructure Evolution of Cu-Al-Zn Alloys

Micro-mechanics investigation of heterogeneous deformation fields and crack initiation driven by the local stored energy density in austenitic stainless steel welded joints

Effects of stacking fault energy on the deformation behavior of CoNiCrFeMn high-entropy alloys: A molecular dynamics study

Prediction and Rational Design of Stacking Fault Energy of Austenitic Alloys Based on Interpretable Machine Learning and Chemical Composition

Effect of stress amplitude on damage and fracture characteristics of austenitic heat‐resistant steel Sanicro 25 at 973 K