Abstract:Stacking fault energy (SFE) can play a crucial role in plastic deformation and damage mechanisms of face-centered cubic (fcc) metals. This study mainly summarized the following results: (1) With the reduction of SFE, the slip mode of fcc metals gradually changes from a facile cross-slip wavy mode to a planar mode until deformation twinning occurs; (2) The concept of effective SFE is applied to investigate the variation of SFE with dislocation density in the fcc metals, with the increase in dislocation density, the effective SFE increases; (3) The reduction of SFE is not the only factor determining the formation of deformation twins in fcc metals. In terms of calculating the competition between simulated slipping and twinning using the first principles, the critical criterion for forming deformation twinning in fcc metals was established; (4) The fatigue dislocation configuration of high-, medium-, and low-SFE fcc metals were analyzed and the judgment conditions for forming regular persistent slip bands (PSBs) are proposed; (5) With the increase in Al content, the SFE of Cu-Al alloy decreases, resulting in a simultaneous increasing trend in the tensile strength and the uniform elongation due to the increasing planar slip degree; (6) The exponential strain-hardening model can accurately describe the tensile strain-hardening process of Cu-Al alloys. The quantitative relationship among yield strength, tensile strength, and uniform elongation of Cu-Al alloy with different alloy compositions and microstructure states was successfully predicted; (7) With the increase in Al content, the fatigue strength of Cu-Al alloy is improved. Increasing Al content at the same strain amplitude will enhance its low-cycle fatigue life. Based on the experimental results above, it is shown that the alloy composition affects the deformation and damage mechanisms, and the evolution process of microscopic defects (dislocations, twins) in fcc metals and alloys. Thus, it drastically affects the tensile and fatigue properties of the fcc metals and alloys. These results provide experimental evidence and a theoretical basis for improving the mechanical properties and service reliability of fcc metals and alloys via alloy designing.

Effects of SMAT Temperature and Stacking Fault Energy on the Mechanical Properties and Microstructure Evolution of Cu-Al-Zn Alloys

Effect of stacking fault energy on microstructural feature and back stress hardening in Cu-Al alloys subjected to surface mechanical attrition treatment

Effect of stacking fault energy on deformation mechanisms in Cu and Cu-30% Zn alloy with gradient structure obtained by SMAT

Investigation of mechanical properties and microstructural evolution in Cu─Al alloys with gradient structure

Strain hardening behavior and microstructure evolution of gradient-structured Cu-Al alloys with low stack fault energy

Influence of stacking fault energy on defect structures and microhardness of Cu and Cu alloys

Temperature Effect on Stacking Fault Energy and Deformation Mechanisms in Titanium and Titanium-aluminium Alloy

The Defect Structures and Mechanical Properties of Cu and Cu–Al Alloys Processed by Split Hopkinson Pressure Bar

Effects of Stacking Fault Energy on the Deformation Mechanisms and Mechanical Properties of Face-Centered Cubic Metals

Effects of stacking fault energy on deformation induced grain boundary relaxation in nanograined Cu alloys

Ductility Sensitivity to Stacking Fault Energy and Grain Size in Cu–Al Alloys

Correlation of stacking fault energy with deformation mechanism in Cu–(2, 20)Zn alloys

Effects of stacking fault energy on the deformation behavior of CoNiCrFeMn high-entropy alloys: A molecular dynamics study

Improving the Strength and Retaining the Ductility of Microstructural Graded Coarse-Grained Materials with Low Stacking Fault Energy

Generalized Stacking Fault Energy, Ideal Strength and Twinnability of Dilute Mg-based Alloys: A First-Principles Study of Shear Deformation

The effect of stacking fault energy on the formation of nano twin/HCP during deformation in FCC concentrated solid solution (CSS) alloys

Plastic deformation of FCC alloys at cryogenic temperature: the effect of stacking-fault energy on microstructure and tensile behaviour

Interplay of Heat Treatment and Deformation Temperature on the Microstructural Evolution and Mechanical Behavior of SLM AlSi10Mg Alloy

Microstructural evolution of Cu–Al alloys subjected to multi-axial compression

Stacking fault energy induced softening in the nucleation limited plasticity regime: a molecular dynamics study on Cu-Al alloys

Effects Of Temperature And Strain Rate On The Fracture Behaviors Of An Al-Zn-Mg-Cu Alloy