The effect of stacking fault energy on the formation of nano twin/HCP during deformation in FCC concentrated solid solution (CSS) alloys

Qingqing Ding,Yongkang Li,Jie Ouyang,Xiao Wei,Ze Zhang,Yanfei Gao,Hongbin Bei

DOI: https://doi.org/10.1016/j.mtnano.2023.100407

IF: 10.3

2023-12-01

Materials Today Nano

Abstract:The exceptional mechanical properties of face-centered cubic (FCC) concentrated solid solution (CSS) alloys generally correlate various deformation mechanisms, such as deformation induced nano twins and/or hexagonal close packed (HCP) phases, which is normally determined by stacking fault energy (SFE). To systemically change the SFE but keep the influence of atomic size and modulus mismatches minimum, a series of NiCo-based alloys are designed by adjusting the Ni/Co ratio. All alloys are fabricated to be single phase FCC with grain size carefully controlled to be ∼60 μm. Deformation substructures after tensile tests over temperature ranging from 77 K to 1073 K are carried out to reveal the effect of SFE on mechanical properties and deformation mechanism. SFE has little effect on yield strength (YS) at all test temperature, but do affect the ultimate tensile strength (UTS) and elongation to fracture (EF) of the alloys. At temperature lower than 873 K, it seems that the lower the SFE, the higher the UTS. At 1073 K, there is no obvious trend for UTS and EF, indicating that SFE has little effect on deformation behavior of alloys at high temperature. Formation of deformation nano twin/HCP depends on not only the SFE of the alloys but also the temperature. As testing temperature and/or SFE of the alloys decreases, deformation induced nano twin/HCP are favorable and become dominant deformation modes for the FCC CSS alloys, resulting in a combination of high strength and good plasticity due to the great work hardening capacity.

materials science, multidisciplinary,nanoscience & nanotechnology

What problem does this paper attempt to address?

This paper aims to study the effect of stacking fault energy (SFE) on the mechanical properties and deformation mechanisms of face-centered cubic (FCC) high-concentration solid solution alloys (CSS alloys) during deformation. Specifically, the paper systematically changes the SFE by adjusting the Ni/Co ratio while minimizing the impact of atomic size and modulus mismatch. The study found: 1. **Effect of SFE on Yield Strength (YS)**: SFE has almost no effect on yield strength at all tested temperatures. 2. **Effect of SFE on Ultimate Tensile Strength (UTS) and Fracture Elongation (EF)**: At temperatures below 873 K, the lower the SFE, the higher the UTS; however, at 1073 K, SFE has no significant effect on UTS and EF. 3. **Formation of Nano-twins and HCP Phase**: The formation of nano-twins and hexagonal close-packed (HCP) phase depends not only on SFE but also on temperature. As the test temperature or SFE decreases, deformation-induced nano-twins and HCP phase become more favorable, becoming the main deformation mode of FCC CSS alloys, thus leading to a combination of high strength and good ductility. Through these studies, the paper reveals the impact of SFE on the deformation mechanisms and mechanical properties of FCC CSS alloys at different temperatures, providing a theoretical basis for designing or optimizing the next generation of FCC CSS alloys.

The effect of stacking fault energy on the formation of nano twin/HCP during deformation in FCC concentrated solid solution (CSS) alloys

Effects of stacking fault energy on the deformation behavior of CoNiCrFeMn high-entropy alloys: A molecular dynamics study

Inherent and Multiple Strain Hardening Imparting Synergistic Ultrahigh Strength and Ductility in a Low Stacking Faulted Heterogeneous High-Entropy Alloy

Highly Pressurized Helium Nanobubbles Promote Stacking-Fault-mediated Deformation in FeNiCoCr High-Entropy Alloy

The universality of strength and plastic deformation in FCC concentrated solid solution (CSS) alloys at room and cryogenic temperatures

Stacking fault induced hardening and grain size effect in nanocrystalline CoNiCrFeMn high-entropy alloy

Influence of lattice distortion on stacking fault energies of CoCrFeNi and Al-CoCrFeNi high entropy alloys

Effect of Strain on the Intrinsic Stacking Fault Energy of Fcc Co: a First-Principles Study

Origins of strengthening and toughening effects in twinned nanocrystalline alloys of low stacking fault energy with heterogeneous grain structure

Impact of interstitial elements on the stacking fault energy of an equiatomic CoCrNi medium entropy alloy: theory and experiments

Effect of strain on generalized stacking fault energies and plastic deformation modes in fcc-hcp polymorphic high-entropy alloys: A first-principles investigation

Twin boundary migration and reactions with stacking fault tetrahedron in Cu and CoCrCuFeNi high-entropy alloy

High stress twinning in a compositionally complex steel of very high stacking fault energy

Composition-dependent slip planarity in mechanically-stable face centered cubic complex concentrated alloys and its mechanical effects

An in situ ambient and cryogenic transmission electron microscopy study of the effects of temperature on dislocation behavior in CrCoNi-based high-entropy alloys with low stacking-fault energy

Unexpected sluggish martensitic transformation in a strong and super-ductile high-entropy alloy of ultralow stacking fault energy

Effects of Alloying Elements on the Stacking Fault Energies of Ni58Cr32Fe10 Alloys: A First-Principle Study

Effect of stacking fault energy on deformation mechanisms in Cu and Cu-30% Zn alloy with gradient structure obtained by SMAT

Investigations on the role of chemical short-range order in the tensile deformation of FCC Co30Fe16.67Ni36.67Ti16.67 high-entropy alloys via Monte Carlo and molecular dynamics hybrid simulations

Long-Range Influence of Cr on the Stacking Fault Energy of Cr-Containing Concentrated Solid-Solution Alloys

Molecular dynamics study on the strengthening mechanisms of Cr–Fe–Co–Ni high-entropy alloys based on the generalized stacking fault energy