Abstract:<p>The deformation mechanism and mechanical properties of pure copper and copper-zinc alloys with low stacking fault energy (SFE) were investigated primarily. In this paper, pure Cu and Cu-30%Zn samples were processed by surface mechanical attrition treatment (SMAT) at cryogenic temperature. The results show that Cu-30%Zn samples exhibit higher yield strength and better ductility by tensile tests at room temperature. With the same processing time of SMAT, the SMAT-ed Cu-30%Zn samples exhibit an optimized combination of strength and ductility compared with that of the SMAT-ed Cu samples. The in-situ electron backscatter diffraction (EBSD) tests show that there is a high density of geometrically necessary dislocations (GNDs) in SMAT-ed Cu-30%Zn samples with low SFE, thereby forming a strong hetero-deformation induced (HDI) stress strengthening and HDI hardening. Also, the twins promote the accumulation of geometrically necessary dislocations to enhance strength while maintaining good ductility in the Cu − 30%Zn samples.</p>

What problem does this paper attempt to address?

This paper mainly explores the influence of stacking fault energy (SFE) on the deformation mechanism and mechanical properties of pure copper (Cu) and copper alloy containing 30% zinc (Cu - 30%Zn) under the gradient structure. Specifically, the researchers prepared pure copper and Cu - 30%Zn samples at low - temperature conditions through surface mechanical attrition treatment (SMAT), and analyzed the strengthening mechanisms of these samples and the reasons for their good ductility through uniaxial tensile tests, Bauschinger loading - unloading tests, and in - situ electron back - scatter diffraction (EBSD) tests. ### Problems the paper attempts to solve: 1. **Improve material strength while maintaining good ductility**: - Researchers are concerned with how to improve material strength without sacrificing its ductility. This is a major challenge in materials science, especially more prominent in nanostructured materials. 2. **Explore the influence of low stacking fault energy on the deformation behavior of materials**: - Stacking fault energy (SFE) is an important parameter affecting the deformation behavior of materials. Low SFE can promote the generation of partial dislocations at grain boundaries, increase dislocation density and twin density, thereby improving the work - hardening ability and ductility of materials. 3. **Optimization of material properties by gradient structure**: - Through SMAT treatment, the grains on the material surface are refined, while the core region remains coarse - grained. This gradient structure can improve material strength and maintain good ductility through the heterogeneous deformation - induced (HDI) stress strengthening and hardening mechanisms. ### Main findings: - **Improvement of mechanical properties**: - The Cu - 30%Zn samples after SMAT treatment show higher yield strength and better ductility. Compared with the untreated samples, the yield strength of the Cu - 30%Zn samples after SMAT treatment increases by 93 MPa, while the uniform elongation only decreases by 13%. - **Changes in microstructure**: - After SMAT treatment, the grains on the sample surface are significantly refined, which is the main reason for the increase in yield strength. Meanwhile, due to low SFE, more twins are formed in the Cu - 30%Zn samples during the SMAT process. These twins can impede the movement of dislocations and store dislocations in front of the twin boundaries, thereby further improving the strength and ductility of the material. - **HDI stress strengthening and hardening**: - During the deformation process, geometrically necessary dislocations (GNDs) accumulate near the heterogeneous interface, producing HDI stress strengthening and hardening effects, which help to simultaneously improve the strength of the material and maintain good ductility. ### Conclusion: Through SMAT treatment, the Cu - 30%Zn samples obtain an excellent combination of strength and ductility. The combination of low SFE and gradient structure enables these samples to maintain good ductility while increasing strength. This research provides new ideas for designing materials with excellent mechanical properties.

Effect of stacking fault energy on deformation mechanisms in Cu and Cu-30% Zn alloy with gradient structure obtained by SMAT

Effects of SMAT Temperature and Stacking Fault Energy on the Mechanical Properties and Microstructure Evolution of Cu-Al-Zn Alloys

Correlation of stacking fault energy with deformation mechanism in Cu–(2, 20)Zn alloys

Influence of stacking fault energy on defect structures and microhardness of Cu and Cu alloys

Strain hardening behavior and microstructure evolution of gradient-structured Cu-Al alloys with low stack fault energy

Investigation of mechanical properties and microstructural evolution in Cu─Al alloys with gradient structure

Effects of stacking fault energy on the deformation behavior of CoNiCrFeMn high-entropy alloys: A molecular dynamics study

Effects of stacking fault energy on deformation induced grain boundary relaxation in nanograined Cu alloys

Inherent and Multiple Strain Hardening Imparting Synergistic Ultrahigh Strength and Ductility in a Low Stacking Faulted Heterogeneous High-Entropy Alloy

Effect of stacking fault energy on nucleation limited plasticity in Cu-Al alloys

Ductility Sensitivity to Stacking Fault Energy and Grain Size in Cu–Al Alloys

Effect of strain on the stacking fault energy of copper: A first-principles study

The effect of stacking fault energy on the formation of nano twin/HCP during deformation in FCC concentrated solid solution (CSS) alloys

Effect of Stacking Fault Energy on the Grain Structure Evolution of FCC Metals During Friction Stir Welding

Investigation of Mechanical Properties and Microstructural Evolution in Pure Copper with Dual Heterostructures Produced by Surface Mechanical Attrition Treatment

Deformation of Fe and Ag Precipitates in Cu Matrix

Stacking fault energy induced softening in the nucleation limited plasticity regime: a molecular dynamics study on Cu-Al alloys

Origins of strengthening and toughening effects in twinned nanocrystalline alloys of low stacking fault energy with heterogeneous grain structure

Deformation stacking fault probability and dislocation microstructure of cold worked Cu–Sn–5Zn alloys by x-ray diffraction line profile analysis

Effect of prefatigue deformation on the uniaxial tensile properties of a dilute Cu-Al alloy

Can experiment determine the stacking fault energy of metastable alloys?