Abstract:Journal of Fire Sciences, Ahead of Print. The fire growth rate of interior linings, furnishings, and construction materials is measured in full-scale fire tests such as the ASTM E84 Steiner Tunnel, the ISO 9705 room fire, and a passenger aircraft fuselage as the flame-spread rate, time-to-flashover, or time to incapacitation, respectively. The results are used to indicate the level of passive fire protection afforded by the combustible material or product in the test without providing any insight into the burning process. These large-scale tests require many square meters of product, are very expensive to conduct, and can exhibit poor repeatability–making them unsuitable for product development, quality control, product surveillance, or regulatory compliance. For this reason, smaller (0.01 m2) samples are tested in bench-scale fire calorimeters under controlled conditions, and these one-dimensional burning histories are correlated with the results of the two- and three-dimensional burning histories in full-scale fire tests by a variety of empirical and semi-empirical fire propagation indices, as well as analytic and computer models specific to the full-scale fire test. The approach described here defines the potential of a material to grow a fire in terms of cone calorimeter data obtained under standard conditions. The fire growth potential, λ (m2/J), is the coupled process of surface flame spread and in-depth burning that is defined as the product of ignitability (1/Eign) and combustibility (ΔQ/ΔE) obtained from a combustion energy diagram measured in a cone calorimeter at an external radiant energy flux [math] (W/m2) above the critical flux for burning, [math]. However, the potential for fire growth, λ≡ (1/Eign)(ΔQ/ΔE) is only realized as a hazard when the heat of combustion of the product per unit surface area, Hc (J/m2), is sufficient to grow the fire. The dimensionless fire hazard of a combustible product of thickness b is therefore, Π = λHc, while the fire hazard of the component materials is an average over the product thickness, π = Π/b. The measurement of λ, Π, and π from combustion energy diagrams of heat release Q (J/m2) versus incident energy E (J/m2) is described, as well as a physical basis for a fire growth potential that provides simple analytic forms for λ in terms of the parameters reported in cone calorimeter tests. Experimental data from the literature show that rapid fire growth in full-scale fire tests of combustible materials occurs above a value of Π determined by the severity of the fire test.

Experimental investigations of the combustion efficiency for fire load calculations

Assessing an Experimental Approach for Chemical Explosive Mode and Heat Release Rate Using DNS Data

A New Hybrid Heating Method Used in Fire Test

Experimental and Numerical Investigations of Heat Impact and Flame Heights from Fires in SBI Tests

An Experimental Study on the Combustion Characteristics of Major Combustible Materials in Office Buildings

Experimental investigations of the fire behavior of composites impacted by kerosene/air turbulent flame

An Experimental and Numerical Study on Fire Behaviors of Charring Materials Frequently Used in Buildings

Efficiency of Sustained Burning of Layered Leaf Fuels under External Radiant Heat Flux

Materials identification in comparison of results among fire scaling and flammability studies

Measuring the fire growth potential of combustible solids using a cone calorimeter

Experimental and Numerical Investigations on Fire Development in a Timber-Based Compartment with Identification of Characteristic Events

Numerical investigations on combustion characteristics of full-size cabin fire with typical material pyrolysis and burnout under different fire source positions

Doorway Calorimetry for Heat Release Rate Measurement in Building Fires

Experimental Study of Transitional Behavior of Fully Developed Under-Ventilated Compartment Fire and Associated Facade Flame Height Evolution

Experimental studies of the effect of burner location on the development of building fires

Experimental Study on Ignition and Combustion Characteristics of Fibre-Reinforced Phenolic Composite

Reduced scale test bench for investigating the upward flame heat impact on external thermal insulation composite system facades

An Experimental Investigation of Burning Behaviour of Liquid Pool Fire in Corridor-Like Enclosures

Temperature Evolution Within Fire Compartment, External Flame Structure Characteristic and Merging Behavior with Multiple-Openings

Radiative Heat Flux Measurement in a Semi-Industrial Oxyfuel Combustion Chamber with Biomass and Coal

Analytical determination of compounds released during pyrolysis, smoldering, and combustion experiments with insulation materials from renewable resources