Abstract:Journal of Fire Sciences, Ahead of Print. The fire growth rate of interior linings, furnishings, and construction materials is measured in full-scale fire tests such as the ASTM E84 Steiner Tunnel, the ISO 9705 room fire, and a passenger aircraft fuselage as the flame-spread rate, time-to-flashover, or time to incapacitation, respectively. The results are used to indicate the level of passive fire protection afforded by the combustible material or product in the test without providing any insight into the burning process. These large-scale tests require many square meters of product, are very expensive to conduct, and can exhibit poor repeatability–making them unsuitable for product development, quality control, product surveillance, or regulatory compliance. For this reason, smaller (0.01 m2) samples are tested in bench-scale fire calorimeters under controlled conditions, and these one-dimensional burning histories are correlated with the results of the two- and three-dimensional burning histories in full-scale fire tests by a variety of empirical and semi-empirical fire propagation indices, as well as analytic and computer models specific to the full-scale fire test. The approach described here defines the potential of a material to grow a fire in terms of cone calorimeter data obtained under standard conditions. The fire growth potential, λ (m2/J), is the coupled process of surface flame spread and in-depth burning that is defined as the product of ignitability (1/Eign) and combustibility (ΔQ/ΔE) obtained from a combustion energy diagram measured in a cone calorimeter at an external radiant energy flux [math] (W/m2) above the critical flux for burning, [math]. However, the potential for fire growth, λ≡ (1/Eign)(ΔQ/ΔE) is only realized as a hazard when the heat of combustion of the product per unit surface area, Hc (J/m2), is sufficient to grow the fire. The dimensionless fire hazard of a combustible product of thickness b is therefore, Π = λHc, while the fire hazard of the component materials is an average over the product thickness, π = Π/b. The measurement of λ, Π, and π from combustion energy diagrams of heat release Q (J/m2) versus incident energy E (J/m2) is described, as well as a physical basis for a fire growth potential that provides simple analytic forms for λ in terms of the parameters reported in cone calorimeter tests. Experimental data from the literature show that rapid fire growth in full-scale fire tests of combustible materials occurs above a value of Π determined by the severity of the fire test.

Materials identification in comparison of results among fire scaling and flammability studies

Compare the flammability of two extruded polystyrene foams with micro-scale combustion calorimeter and cone calorimeter tests

A comparative study of test methods for assessment of fire safety performance of bus interior materials

Correlating the Performance of a Fire-Retardant Coating across Different Scales of Testing

Study on Influence of Test Methods for Determining Explosion Limits of Flammable Refrigerants

Fire Risk Rating Assessment for Wood Specimens Coated with Flame Retardant

Current Status and Prospects of Plant Flammability Measurements

Some relevant parameters for assessing fire hazards of combustible mine materials using laboratory scale experiments

Measuring the fire growth potential of combustible solids using a cone calorimeter

Study on correlation between measurements of flame retardancy ofpolymer materials

Experimental investigations of the combustion efficiency for fire load calculations

A Study of Thermal Degradation and Fire Behaviour of Polymer Composites and Their Gaseous Emission Assessment

A Review of Combustion and Flame Spread over Thermoplastic Materials: Research Advances and Prospects

Fire Safety Research Institute Materials and Products database—A resource to support fire modeling

Sensitivity Analysis for an Effective Transfer of Estimated Material Properties from Cone Calorimeter to Horizontal Flame Spread Simulations

Numerical investigations on combustion characteristics of full-size cabin fire with typical material pyrolysis and burnout under different fire source positions

A Comparative Experimental Study on Heat Release Rates of Charring and Noncharring Solid Combustible Materials

Fire Safety for Green Façades: Part 1: Basics, State-of-the-Art Research and Experimental Investigation of Plant Flammability

Particle Size Influence on the Transport Classification Labels and Other Flammability Characteristics of Powders

Investigation of the Flammability of Different Textile Fabrics Using Micro-Scale Combustion Calorimetry