Abstract:The objective of this work was to investigate and evaluate the effect of the cooling environment on the microstructure, secondary phase precipitates and mechanical properties of an as-cast cobalt alloy. The microstructure of castings has a large bearing on the mechanical properties, grain size, porosity and the morphology of carbide precipitates are thought to influence hardness, tensile strength and ductility. It is postulated that a greater understanding of microstructure and secondary phase precipitate response to casting parameters could lead to the optimisation of casting parameters and serve to reduce the requirement of thermo-mechanical treatments currently applied to refine as-cast structures and achieve adequate mechanical properties. Thermal analysis was performed to determine the critical stages of cooling. Ten millimetre diameter cylindrical specimens which could be machined into tension test specimens were cast and cooled under different conditions to impose different cooling rates. Analytical techniques such as optical microscopy (OM), scanning electron microscopy (SEM), energy dispersive x-ray spectroscopy (EDX), tensile testing and micro-hardness testing were used to study the specimens. Parameters studied include grain size, secondary dendrite arm spacing, secondary phase precipitates, porosity, hardness, ultimate tensile strength, yield strength and elongation. The microstructure of as-cast Co-28Cr-6Mo was found to consist of a dendritic matrix with secondary phases precipitated at grain boundaries and interdendritic zones. These secondary phase precipitates consist of carbides, rich in chromium and molybdenum. The size and area fraction of carbides was found to decrease significantly with increasing cooling rate while the micro-porosity was only marginally affected. The as-cast grains are illustrated for the first time showing a significant difference in size between insulated and naturally cooled specimens. The secondary dendrite arm spacing was determined to be significantly affected by the various cooling environments and the mechanical properties of hardness, ultimate tensile strength and yield strength all increased with increasing cooling rate while the ductility decreased. Correlations between microstructural features and mechanical properties are proposed.

Study on the eutectic and post-eutectic reactions in LM13 aluminum alloy using cooling curve thermal analysis technique

Influence of heat treatment on morphology and quantity of eutectic phases of Al alloys with different cooling rates

Effect of Different Cooling Rates Condition on Thermal Profile and Microstructure of Aluminium 6061

Effect of cooling rate and Al content on solidification characteristics of AZ magnesium alloys using cooling curve thermal analysis

Effect of Cooling Rate on Solidification Parameters and Microstructure of Al-7Si-0.3Mg-0.15Fe Alloy

Non-equilibrium solidification of bulk undercooled Ni–P eutectic alloys

Microstructure Refinement Mechanism of Undercooled Cu55Ni45 Alloys

Effects of Cooling Rate on the Solidification Process of Pure Metal Al: Molecular Dynamics Simulations Based on the MFPT Method

Application of thermal analysis in solidification process of undercooled Fe-B alloy

Effect of Cooling Rate on Microstructure and Mechanical Properties of Sand-Casted Al–5.0Mg–0.6Mn–0.25Ce Alloy

Influence of Cooling Rate on Solidification Behavior of Sand-Cast Mg–10Gd–3Y–0.4Zr Alloy

SOLIDIFICATION BEHAVIOR AND MICROSTRUCTURE EVOLUTION OF Fe83B17 EUTECTIC ALLOY UNDER HYPER-UNDERCOOLING

Effect of Cooling Rate on the Grain Morphology and Element Segregation Behavior of Fe-Mn-Al-C Low-Density Steel During Solidification

Effect of Cooling Rate on Microstructure and Mechanical Properties of an Al-5.0Mg-3.0Zn-1.0Cu Cast Alloy

cooling rate control and solidified microstructure of Al-7.7Ca eutectic alloy during aerodynamic levitation

The influence of cooling conditions on grain size, secondary phase precipitates and mechanical properties of biomedical alloy specimens produced by investment casting

Prediction of the Solidification Path of Al-6.32cu-25.13mg Alloy by A Unified Microsegregation Model Coupled with Thermo-Calc

Study on the Eutectic Modification Level of Al–7Si Alloy by Computer Aided Recognition of Thermal Analysis Cooling Curves

Effects of Cooling Rate on Microstructure, Mechanical Properties, and Residual Stress of Fe-2.1B (wt%) Alloy

Prediction of the Solidification Path of Al-4.37cu-27.02mg Ternary Eutectic Alloy with A Unified Microsegregation Model Coupled with Thermo-Calc

Effect of ultrasonic melt processing and cooling rate on microstructure evolution of Al–Cu–Mn–Mg–Fe–Si alloy