Abstract:Engineered artificial minerals (EnAMs) are the core of a new concept of designing scavenger compounds for the recovery of critical elements from slags. It requires a fundamental understanding of solidification from complex oxide melts. Ion diffusivity and viscosity play vital roles in this process. In the melt, phase separations and ion transport give rise to gradients/increments in composition and, with it, to ion diffusivity, temperature, and viscosity. Due to this complexity, solidification phenomena are yet not well understood. If the melt is understood as increments of simple composition on a microscopic level, then the properties of these are more easily accessible from models and experiments. Here, we obtain these data for three stoichiometric lithium aluminum oxides. LiAlO2 is a promising EnAM for the recovery of lithium from lithium-ion battery pyrometallurgical processing. It is obtained through the addition of aluminum to the recycling slag melt. The high temperature properties spanning from below to above the liquidus temperature of three stoichiometric Li-Al-Oxides: Li5AlO4, LiAlO2, and LiAl5O8 are determined using molecular dynamic simulations. The compounds are also synthesized via the sol-gel route. The Li+ ion exhibits the largest diffusivity. They are quite mobile already below the liquidus temperature, i.e., for LiAlO2 at T = 1700 K, the diffusion coefficient of the lithium ion equals D = 3.0 × 10-9 m2 s-1. The other ions Al3+ and O2- do not move considerably at that temperature. The diffusivity of Li+ is largest in the lithium-rich compound Li5AlO4 with D = 32 × 10-9 m2 s-1 at 2500 K. The lower the viscosity, the higher the lithium content. The Li5AlO4 exhibits a viscosity of η = 2.2 mPa s at 1328 K which matches well with the experimentally determined 2.5 mPa s at this temperature. The viscosity of LiAlO2 at 1800 K is more than two times higher. These data sets can help to describe the melts on a microscopic level and understand how the melt properties will change due to gradients in the Li/Al concentration.

Cooling Curves of Concentrated Alloys, Steelmaking Slag, and Lithium Iron Phosphate

High-temperature Oxidation Behavior of AlCoCrCuFeNi High-Entropy Alloy by Selective Laser Melting

Non-equilibrium solidification of bulk undercooled Ni–P eutectic alloys

Effect of Cooling Rate on the Grain Morphology and Element Segregation Behavior of Fe-Mn-Al-C Low-Density Steel During Solidification

Microstructure Formation of Al-Based Alloys in the Presence of Rare Earth Metals (Ce, La) and Mn under High Cooling Rate

Pattern Recognition of Thermal Analysis Cooling Curves and Quality Evaluation of Melt Cast Alloys

Computational Thermodynamics/kinetics Aided Design for the Microstructure of Pearlitic Steels During Cooling Process

Engineering Compounds for the Recovery of Critical Elements from Slags: Melt Characteristics of Li5AlO4, LiAlO2, and LiAl5O8

Experimental Study of High Temperature Phase Equilibria in the Iron-Rich Part of the Fe-P and Fe-C-P Systems

Application of thermal analysis in solidification process of undercooled Fe-B alloy

A High-Throughput Study of Magnetocaloric Materials: Gradient Solidification Applied to La-Fe-Si

Study on the eutectic and post-eutectic reactions in LM13 aluminum alloy using cooling curve thermal analysis technique

Microstructure Evolution and Mechanical Properties of a Cast and Heat-Treated Al–Li–Cu–Mg Alloy: Effect of Cooling Rate During Casting

A comparative study of metastable phase separation for undercooled liquid Fe35Cu65 alloy under natural and forced cooling conditions

Phase constitution, microstructure evolution and magnetocaloric properties of LaFe<sub>11.8</sub>Si<sub>1.2</sub> strip-casting flakes

Microstructural Evolution, Magnetocaloric Effect, Mechanical and Thermal Properties of Hot-Pressed LaFe11.6Si1.4/Ce2Co7 Composites Prepared Using Strip-Cast Master Alloy Flakes

Evaluating Melt Iron Features by Computer Aided Recognition of Thermal Analysis Cooling Curves

Secondary Phase Precipitation in Fe-22Mn-9Al-0.6C Low-Density Steel during Continuous Cooling Process

Tailoring Thermal Conductivity and Microstructure of Al-Fe Alloys by Addition of Sc2O3 and Variable Cooling Rates

Effects of cooling manner on Laves phase precipitation and mechanical properties of Al modified super ferritic stainless steels

Thermodynamics‐Guided High‐Throughput Discovery of Eutectic High‐Entropy Alloys for Rapid Solidification