Abstract:Thermal analysis and microstructure characterization provide information regarding material thermal profiles and microstructure formation. Wrought aluminium alloys offer significant advantages in terms of higher ultimate tensile strength (UTS) and yield strength but relatively poor fluidity properties. The objective of this experiment presented in this paper was to understand the relationship between solidification rate, metallurgical behaviour, and fraction phase growth of wrought aluminium 6061. This information was crucial and important to the foundry industry to understand the material behaviour that will help to cast wrought aluminium 6061. Thermal analysis and microstructure of wrought aluminium 6061 on different cooling conditions are present in this paper. In this work, Aluminium 6061 heated and melted in a graphite crucible at a temperature of 800°C. Two thermocouples located at the centre and 20 mm from the graphite crucible wall. Slow cooling rate condition experiment rig was developed by placing graphite crucible into a chamber with kaowool insulation. Normal cooling rate condition was developed by allowing the molten solidify at room temperature. Fast cooling rate condition was prepared by applying a forced airflow over the graphite crucible. The slow, normal, and high cooling rates were calculated at 0.03°C/s, 0.2°C/s and 0.3°C/s respectively. Cooling curve analysis was performed to predict various areas of solidification phase and fraction solid. In Addition, the microstructure formation was observed, recorded, and compared between different cooling conditions. The results show slow cooling rate condition formation of eutectic and solidus temperatures occurred far from liquidus temperature. The eutectic and solidus temperature was increased with the increment of the cooling rate. Furthermore, the DCP temperature of slow cooling rate condition at 638.3°C was the lowest while gives wider temperature range corresponding to the fraction solid percentage increment. Meanwhile, an increase in cooling rate refined the microstructure, improved the grain circularity and at the same time reduced the aspect ratio.

Control of Grain Refinement of A356 Aluminum Alloy by Computer Aided Cooling Curve Analysis

Study on Influence of Surface Coating During Cooling Slope Rheocasting Process

Quality Assessment of Aluminum-Based Grain Refining Master Alloys

Study on the eutectic and post-eutectic reactions in LM13 aluminum alloy using cooling curve thermal analysis technique

Recognition of thermal analysis cooling curves and refinement of molten Al-7Si alloys

Grain Refinement in A Alznmgcuti Alloy by Intensive Melt Shearing: A Multi-Step Nucleation Mechanism

Effect of Different Cooling Rates Condition on Thermal Profile and Microstructure of Aluminium 6061

Impact of Transition-Metal Elements on Grain Refiner Performance in AA6061

Effective Inhibition of Anomalous Grain Coarsening in Cast AZ91 Alloys During Fast Cooling Via Nanoparticle Addition

Demonstrating the roles of solute and nucleant in grain refinement of additively manufactured aluminium alloys

Nucleation Catalysis in Aluminum Alloy A356 Using Nanoscale Inoculants

Grain Refining Efficiency of Al-V-B Master Alloy in A356.2 Alloy under Different Inoculated Temperatures and Holding Times

Cooling-Assisted Ultrasonic Grain Refining of Aluminum E380 Die Casting Alloy

Grain Refinement of Al–Si Alloy (A356) by Melt Thermal Treatment

Assessment of Modification Level of Hypoeu- Tectic Al-Si Alloys by Pattern Recognition of Cooling Curves

Effect of cooling rate on the grain refinement of TiAl-based alloys by rapid heat treatment

Understanding the grain refinement mechanisms in aluminium 2319 alloy produced by wire arc additive manufacturing

Efficiency of different commercial TiBAl grain refiners on refinement of pure aluminum cast structures

Effects of Annular Electromagnetic Stirring Coupled with Intercooling on Grain Refinement and Homogeneity During Direct Chill Casting of Large-Sized 7005 Alloy Billet

Accurate Simulation of Complex Temperature Field in Counter-Pressure Casting Process Using A356 Aluminum Alloy

Correlation of Recalescence with Grain Refinement of Magnesium Alloys