Abstract:In this study, the microstructural evolution, particularly precipitation behavior, and mechanical properties of cast Al–Li–Cu–Cd–Mn–Zr–Ti alloy during heat treatment are systematically examined. It provides a detailed discussion of the underlying mechanisms involved. After aging at 160 °C for 24 h, the alloy exhibits an excellent combination of strength and elongation, surpassing other cast Al–3Li–2Cu–X alloys reported in the literature. The microstructural evolution and mechanical properties of cast Al–Li–Cu–Cd–Mn–Zr–Ti alloy during heat treatment are investigated systematically. In these findings, it is shown that the as‐cast alloy exhibits fine and equiaxed grains. During the solid solution treatment, Al20Cu2Mn3 dispersoids effectively restrict grain growth, and reducing the solid solution time has a similar effect. Subsequently, the precipitation behavior and its effect on the mechanical properties during the aging process are revealed. Al3(Ti, Zr) particles are uniformly distributed throughout the matrix, acting as nucleation sites for δ′, θ′, and T1 precipitates. Overtime, δ′ precipitates gradually coarsen and decrease in number, and some δ′ precipitates attach to Al3(Ti, Zr) particles, forming core–shell Al3(Li, Ti, Zr) phases. At the same time, plate‐shaped θ′ and T1 precipitates emerge and coarsen. After aging at 160 °C for 24 h, the alloy exhibits an excellent combination of strength (yield strength =293.3 ± 4 MPa, ultimate tensile strength =468.0 ± 3 MPa) and ductility (elongation =9.6 ± 0.4%), surpassing those reported in other cast Al–3Li–2Cu–X alloys. Critically, the underlying mechanisms behind the microstructure and mechanical properties are discussed extensively, providing valuable insights for the advancement of cast Al–Li alloys.

Impact of Transition-Metal Elements on Grain Refiner Performance in AA6061

Efficiency of different commercial TiBAl grain refiners on refinement of pure aluminum cast structures

An experimental study of the effect of Ag, Cu, Li, Mg, Ni, Ti, Sc, Zr on grain refining in binary and multicomponent Al-based alloys

The grain refinement of high-purity aluminum by aluminum-transition metal alloys

Investigation of the Effect of Grain Refinement on the Mechanical Properties of 6082 Aluminium Alloy

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

Grain Refinement of Al-5Ti-0.62C-0.2Nd Grain Refiner for Commercial Pure Aluminum and Its Effect on Mechanical Properties

Effect of Grain Refinement on the Microstructure and Tensile Properties of Cast Aluminum A356.2 Alloy Knuckles Made by Counter Pressure Casting (CPC) Process

Effect of Alloying Elements and Processing Parameters on Microstructure and Properties of 1XXX Aluminium Alloys

Influences of Preparation Conditions and Melt Treatment Procedures on Melt Treatment Performance of Al-5Ti-B and Al-10Sr Master Alloys

Research on Grain Refinement of Sc and Zr Addition in an Al-Mg-Zn Alloy from Experiments and First-Principles Calculations

Understanding the grain refinement mechanisms in aluminium 2319 alloy produced by wire arc additive manufacturing

Quantifying the effects of grain refiners (AlTiB and Y) on microstructure and properties in W319 alloys

Optimization of Melt Treatment for Austenitic Steel Grain Refinement

Effect of Grain Refinement on the Dynamic, Mechanical Properties, and Corrosion Behaviour of Al-Mg Alloy

Enhanced grain refinement and mechanical properties of a high–strength Al–Zn–Mg–Cu–Zr alloy induced by TiC nano–particles

Multi-alloying effect of Ti, Mn, Cr, Zr, Er on the cast Al-Zn-Mg-Cu alloys

Effects of Foundry Variables and Refiners on Cast Structures of Superalloy K4169i. Grain Structures and Grain Refinement Mechanisms

Microstructural Evolution, Precipitation Behavior, and Mechanical Property Response of Cast Al–Li–Cu–Cd–Mn–Zr–Ti Alloy

Performance Comparison of AlTiC and AlTiB Master Alloys in Grain Refinement of Commercial and High Purity Aluminum

Effect of Scandium on Grain refinement mechanism and Mechanical Properties of Al-7Si-0.6Mg alloy at Different Cooling Rates