Abstract:Thermal analysis and microstructure characterization provide information regarding material thermal profiles and microstructure formation. Wrought aluminium alloys offer significant advantages in terms of higher ultimate tensile strength (UTS) and yield strength but relatively poor fluidity properties. The objective of this experiment presented in this paper was to understand the relationship between solidification rate, metallurgical behaviour, and fraction phase growth of wrought aluminium 6061. This information was crucial and important to the foundry industry to understand the material behaviour that will help to cast wrought aluminium 6061. Thermal analysis and microstructure of wrought aluminium 6061 on different cooling conditions are present in this paper. In this work, Aluminium 6061 heated and melted in a graphite crucible at a temperature of 800°C. Two thermocouples located at the centre and 20 mm from the graphite crucible wall. Slow cooling rate condition experiment rig was developed by placing graphite crucible into a chamber with kaowool insulation. Normal cooling rate condition was developed by allowing the molten solidify at room temperature. Fast cooling rate condition was prepared by applying a forced airflow over the graphite crucible. The slow, normal, and high cooling rates were calculated at 0.03°C/s, 0.2°C/s and 0.3°C/s respectively. Cooling curve analysis was performed to predict various areas of solidification phase and fraction solid. In Addition, the microstructure formation was observed, recorded, and compared between different cooling conditions. The results show slow cooling rate condition formation of eutectic and solidus temperatures occurred far from liquidus temperature. The eutectic and solidus temperature was increased with the increment of the cooling rate. Furthermore, the DCP temperature of slow cooling rate condition at 638.3°C was the lowest while gives wider temperature range corresponding to the fraction solid percentage increment. Meanwhile, an increase in cooling rate refined the microstructure, improved the grain circularity and at the same time reduced the aspect ratio.

Effect of cooling rate and Al content on solidification characteristics of AZ magnesium alloys using cooling curve thermal analysis

Effect of cooling rate on microstructure and mechanical properties of Mg-9Gd-4Y-1Zn-1Al alloy

Effect of Cooling Rate on Solidification Parameters and Microstructure of Al-7Si-0.3Mg-0.15Fe Alloy

Influence of Cooling Rate on Solidification Behavior of Sand-Cast Mg–10Gd–3Y–0.4Zr Alloy

The Effect of Cooling Rate on the Microstructure and Mechanical Properties of Mg–Zn–Gd-based Alloys

Effects of Cooling Rates on the Solidification Process of Al-Si-Mg Alloy

Effect of cooling rate on the microstructure and mechanical properties of sand-casting Mg-10Gd-3Y-0.5Zr magnesium alloy

Study on the eutectic and post-eutectic reactions in LM13 aluminum alloy using cooling curve thermal analysis technique

Effect of Different Cooling Rates Condition on Thermal Profile and Microstructure of Aluminium 6061

Effects of Cooling Rate on the Solidification Process of Pure Metal Al: Molecular Dynamics Simulations Based on the MFPT Method

Effect of Cooling Rate on the Solidified Microstructure of Mg-Gd-Y-Zr Alloy

Enhancing the Mechanical Properties of Mg–Al Alloy by Introducing Al2Y Nanoparticles Via Rapid-Cooling Solidification and Optimized Heat Treatments

Effect of Cooling Rate on Microstructure and Mechanical Properties of an Al-5.0Mg-3.0Zn-1.0Cu Cast Alloy

Effect of Cooling Rate on Solidification Structure of Zinc-Aluminum-Magnesium Alloy

Thermal Analysis and Solidification Pathways of Mg–Al–Ca System Alloys

Effect of Cooling Rate on Microstructure and Mechanical Properties of Sand-Casted Al–5.0Mg–0.6Mn–0.25Ce Alloy

Thermal properties of AZ series cast Magnesium alloys

Experimental Study on the Effect of Cooling Rate on the Secondary Phase in As‐Cast Mg–Gd–Y–Zr Alloy

In Situ Observation of Microstructure and Precipitate Phase Transformation during the Solidification of Mg‐Containing GH3625 Alloy at Different Cooling Rates

Effect of Cooling Conditions on Grain Size of AZ91 Alloy

The microstructure, fracture mechanism and their correlation with the mechanical properties of as-cast Mg-Nd-Zn-Zr alloy under the effect of cooling rate