Abstract:Magnesium alloys have received much attention for their lightweight and other excellent properties, such as low density, high specific strength, and good castability, for use in several industrial and commercial applications. However, both magnesium and its alloys show limited room-temperature formability owing to the limited number of slip systems associated with their hexagonal close-packed crystal structure. It is well known that crystallographic texture plays an important role in both plastic deformation and macroscopic anisotropy of magnesium alloys. Many authors have concentrated on improving the room- temperature formability of Mg alloys. However, despite having a lot of excellent properties in magnesium alloy, the study for various properties of magnesium alloy have not been clarified enough yet.Mg alloys are known to have a good damping capacity compared to other known metals and their alloys. Also, the damping properties of metals are generally recognized to be dependent on microstructural factors such as grain size and texture. However, there are very few studies on the relationship between the damping capacity and texture of Magnesium alloys. Therefore, in this study, specimens of the AZ31 magnesium alloy, were processed by hot working, and their texture and damping property investigated. A 60 mm × 60 mm × 40 mm rectangular plate was cut out by machining an ingot of AZ31 magnesium alloy (Mg-3Al-1Zn in mass%), and rolling was carried out at 673 K to a rolling reduction of 30%. Then, heat treatment was carried out at temperatures in the range of 573-723 K for durations in the range of 30-180 min. The samples were immediately quenched in oil after heat treatment to prevent any change in the microstructure. Texture was evaluated on the compression planes by the Schulz reflection method using nickel-filtered Cu Kα radiation. Electron backscatter diffraction measurements were conducted to observe the spatial distribution of various orientations. Specimens for damping capacity measurements were machined from the rolled specimen, to have a length of 120 mm, width of 20 mm, and thickness of 1 mm. The damping capacity was measured with a flexural internal friction measurement machine at room temperature. It was found that the damping capacity increases with both increasing heat-treatment temperature and time, due to grain growth and the increased pole densities of textures.

Effect of Aluminum Concentration on Damping Capacity during Annealing in AZ-Series Magnesium Alloy

Effect of Recrystallization Behavior of AZ31 Magnesium Alloy on Damping Capacity

The Effect of Crystal Orientation on Damping Capacity in Rolled AZ31 Magnesium Alloy

Effect of hot working on the damping capacity and mechanical properties of AZ31 magnesium alloy

Effects of Annealing Treatment on Mechanical and Damping Properties of ZK60 Magnesium Alloy Sheets

Effect of Al Concentration on Basal Texture Formation Behavior of AZ-Series Magnesium Alloys during High-Temperature Deformation

Effect of alloying elements and heat treatment on damping capacity of Mg-Al alloys.

A Study on the Damping Capacities of Mg–Zn–Y-Based Alloys with Lamellar Long Period Stacking Ordered Phases by Preparation Process

Mechanical Properties and Microstructures of Mg-Al-Zn Alloys with High Aluminum Contents

Effect of annealing treatment on the microstructure and mechanical properties of warm-rolled Mg–Zn–Gd–Ca–Mn alloys

Effect of Aging Treatment on Microstructure and Damping Properties of Mg-Al-Ca-Mn-Zn Alloy

The Effects of Rolling Deformation and Annealing Treatment on Damping Capacity of 1200 Aluminium Alloy

Effects of Aging Process on the Damping Performance of ZK60 Magnesium Alloys Prepared by Large Strain Rolling

Effect of annealing process on microstructure and mechanical properties of precipitated phase of A1235 aluminum alloy

Effect of cooling rate on microstructure and mechanical properties of Mg-9Gd-4Y-1Zn-1Al alloy

Simultaneous Improvement of Strength, Ductility and Damping Capacity of Single Β-Phase Mg-Li-Al-Zn Alloys

Influence of Annealing on Tensile Property and Microstructure of AZ31 Magnesium Alloy

Effect of Symmetric and Asymmetric Rolling Processes on The Microstructure and Mechanical Properties of AZ31B Magnesium Alloy

Achieving high damping and excellent ductility of Al Mg alloy sheet by the coupling effect of Mg content and fine grain structure

Effect of Coarse β(Al3Mg2) Phase on Microstructure Evolution in 573 K Annealed Al-10Mg Alloy by Uniaxial Compression

Effect of annealing treatment on the microstructure and mechanical properties of bulk nanostructured Ti/AZ61 composites prepared by hot pressing