Abstract:Al/SiC composites with volume fractions of SiC between 0.55 and 0.71 were made from identical tapped and vibrated powder preforms by squeeze casting (SC) and by two different setups for gas pressure infiltration (GPI), one that allows short (1–2 min) liquid metal/ceramic contact time (fast GPI) and the other that operates with rather long contact time, i.e., 10–15 min, (slow GPI). Increased liquid metal–ceramic contact time is shown to be the key parameter for the resulting thermal and electrical conductivity in the Al/SiC composites for a given preform. While for the squeeze cast samples neither dissolution of the SiC nor formation of Al4C3 was observed, the gas pressure assisted infiltration led inevitably to a reduced electrical and thermal conductivity of the matrix due to partial decomposition of SiC leading to Si in the matrix. Concomitantly, formation of Al4C3 at the interface was observed in both sets of gas pressure infiltrated samples. Longer contact times lead to much higher levels of Si in the matrix and to more Al4C3 formation at the interface. The difference in thermal conductivity between the SC samples and the fast GPI samples could be rationalized by the reduced matrix thermal conductivity only. On the other hand, in order to rationalize the thermal conductivity of the slow GPI a reduction in the metal/ceramic interface thermal conductance due to excessive Al4C3-formation had to be invoked. The CTE of the composites generally tended to decrease with increasing volume fraction of SiC except for the samples in which a large expansive drift was observed during the CTE measurement by thermal cycles. Such drift was essentially observed in the SC samples with high volume fraction of SiC while it was much smaller for the GPI samples.

Influence of Grain Size on Thermal Conductivity of SiC Ceramics

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Effect of β-Si<sub>3</sub>N<sub>4</sub> Powder on Thermal Conductivity of Silicon Nitride Ceramics

Influence of Reinforcement with Multimodal Distribution on Thermophysical Properties and Fracture Behavior in Al-Si/SiC Composites Infiltrated under Super-Gravity Field

Effects of Particle Size on the Thermal Physical Properties of Sicp/Al Composites

Study on Thermal Conductivity of Spark-Plasma-Sintered Silicon Nitride Ceramics

Effects of solid solution, grain size and porosity on the thermal conductivity of aluminum- and boron-added porous silicon carbide ceramics with in-situ grain growth

Influence of Yttria–Alumina Content on Sintering Behavior and Microstructure of Silicon Nitride Ceramics

Thermal conductivity improvement in Si3N4 ceramics via grain purification

Sintering Aids and Thermal Conductivity of Polycrystalline SiC

Fabrication and Surface Hardening Properties for SiC/AlN Ceramic Composites with Different SiC Grain Size

Effect Of Microstructural Modification On Thermal Conductivity And Strength Of Silicon Nitride

Fabrication of Si3N4 ceramics with improved thermal conductivity by carbothermal reduction and two‐step sintering

Effect of Composite Sintering Additives Containing Non-Oxide on Mechanical, Thermal and Dielectric Properties of Silicon Nitride Ceramics Substrate

Phase Transformation, Microstructure and Mechanical Properties of Si3n4/Sic Composite

Influence of SiC particle size on microstructure and mechanical properties of Al2O3-SiC nanocomposites

Fabrication, Microstructure, and Properties of SiC/Al 4 SiC 4 Multiphase Ceramics Via an In-Situ Formed Liquid Phase Sintering

Influence of Stabilizing Ions and Sintering Process on the Thermal Conductivity of Α‐sialon Ceramics

Influence of processing route on electrical and thermal conductivity of Al/SiC composites with bimodal particle distribution

Effects of Particle Size on the Thermal Expansion Behavior of SiCp/Al Composites