Abstract:The influence of the polymer fraction structure on the physico-mechanical properties of bimodal reactor polymer compositions based on ultrahigh molecular weight polyethylene has been studied. The compositions included 30 wt % of the modifying polymer fractions. They represent linear high-density polyethylene with a molecular weight of 160, 110, and 48 kg/mol and branched ethylene/hexene-1 copolymers with the hexene-1 content of 6.3 and 8 mol % introduced into compositions directly in the synthesis. The thermal properties of materials have been studied by means of the DSC method. The presence of linear low molecular weight polyethylene fractions of highly crystallinity (62–83%) in compositions with ultrahigh molecular weight polyethylene of low crystallinity (52.5%) leads to a sharp increase in the content of the crystalline phase in the materials. Compositions with branched copolymer fractions have the lower degree of crystallinity (28.4 and 23%). A correlation was found between the content of the crystalline phase and the values of the elastic modulus of reactor compositions. For compositions including linear low molecular weight polyethylene, there is a sharp increase in this indicator up to 1100–1535 MPa relative to unmodified ultrahigh molecular weight polyethylene (733 MPa) with approach to the values characteristic of pure polyethylene (1230–1670 MPa). Branched copolymer fractions cause a decrease in the modulus of elasticity to 151–345 MPa. All the studied compositions demonstrate sufficiently high strength properties. The values of elongation at break exceed this characteristic of unmodified ultrahigh molecular weight polyethylene (550±36%) and vary in the range from 560±14 to 850±22%. The introduction of modifying polymer fractions led to the appearance of fluidity of compositions based on ultrahigh molecular weight polyethylene.

Structure and mechanical properties of self-reinforced ultra-high molecular weight polyethylene

Effective Enhancement of a Carbon Nanothread on the Mechanical Properties of the Polyethylene Nanocomposite

Fully Aminated Rigid‐rod Aromatic Polyamide Efficiently Reinforces Tetraglycidyl Diamino Diphenyl Methane Epoxy Resin and Its Carbon Fiber Composite

Influence of Interfacial Adhesion on Stress-Strain Properties of Highly Filled Polyethylene

Preparation and Characterization of Electrospun Mat of Ultra-high Molecular Weight Polyethylene/High-Density Polyethylene Blends

Structure and Mechanical Properties of High-Density Polyethylene Composites Reinforced with Glassy Carbon

Extremely high reinforcement of high‐density polyethylene by low loading of unzipped multi‐wall carbon nanotubes

Increasing the Resistance of HDPE to Abrasive Wear with Small Additions of UHMWPE

Preparation and Performance of Carbon Nanotubes Reinforced Ultra-high Molecular Weight Polyethylene Fibre-based Composites

Ultra-High Molecular Weight Polyethylene Fibers/Epoxy Composites: Effect of Fiber Treatment on Properties

Reinforcing High-Density Polyethylene by Polyacrylonitrile Fibers

Investigation of the mechanical and thermal stability of ultra-high molecular weight polyethylene by using amide-multi-walled carbon nanotubes as a reinforcement material

Effect of Carbon Fiber Surface Modification on the Mechanical Properties of Carbon-Fiber-Reinforced Ultrahigh-Molecular-Weight Polyethylene Composite

The effect of simultaneous fiber surface treatment and matrix modification on mechanical properties of unidirectional ultra-high molecular weight polyethylene fiber/epoxy/nanoclay nanocomposites

The mechanical properties of the ultra high molecular weight polyethylene grafted with 3-dimethy (3-(N-methacryamido) propyl) ammonium propane sulfonate

Effect of Borpolymer on Mechanical and Structural Parameters of Ultra-High Molecular Weight Polyethylene

In Situ Synthesized Self-Reinforced HDPE/UHMWPE Composites with High Content of Less Entangled UHMWPE and High Gradient-Distributed Oriented Structures

On the Structural Peculiarities of Self-Reinforced Composite Materials Based on UHMWPE Fibers

Effect of the Polyolefin Fraction Structure on the Morphology and Properties of Polymer Compositions Based on Ultrahigh Molecular Weight Polyethylene

Flow‐field‐assisted Shaping of Linear Low‐density Polyethylene/low‐entanglement Ultra‐high Molecular Weight Polyethylene Blends with Enhanced Mechanical Properties and Thermal Conductivity

Properties of UHMWPE Fibre Reinforced Composites