Abstract:Schematic of sequential melting and sintering process on morphology development of UHMWPE/LDPE blends. Blending ultra‐high molecular weight polyethylene (UHMWPE) with a low molecular weight polyolefin is a well‐established technique to improve its processability. The binary blends of UHMWPE and low‐density polyethylene (LDPE) were prepared with varying LDPE content (10%, 20%, 30%, 40%, and 50% by wt.) leading to the formation of a single polymer composite system (SPCS) as melting and sintering followed preferential stages during mixing. Interestingly, the sequence of either "melting followed by sintering" or "simultaneous sintering and melting" depends on the LDPE content in the blend, resulting in unique blend morphology. Separate melting peaks for the blend's constituents were observed in thermal characterization, showing the blend's immiscibility, while intermediate peaks showed moderate miscibility in the melt state. Due to the high entanglement density, UHMWPE retained a solid‐like structure and showed an intense viscous nature even above the melting point in rheological characterization. Typically, the UHMWPE samples are fabricated by boundary fusion between particles called sintering. At LDPE content higher than 30 wt.%, the sea island structure was visible in morphological analysis, and the preexisting cavities reduced the tensile modulus by 54% in the blend, along with decreased elongation at failure (250%–100%). Similarly, the flexural modulus was reduced by 34.7% in the blends, along with the decreased flexural strength. Interestingly, the decrease in performance properties occurred in two steps over the range of LDPE content. Thus, it was clear that 30 wt.% of LDPE in the UHMWPE/LDPE blend represented the critical concentration for controlling melting and sintering sequence to develop specified morphology and performance properties. These blends have the potential for biomedical application as well as for the development of foam products, which is the further scope of the present study.

Preparation and Characterization of Electrospun Mat of Ultra-high Molecular Weight Polyethylene/High-Density Polyethylene Blends

Exploring the Entangled State and Molecular Weight Ofuhmwpeon the Microstructure and Mechanical Properties Ofhdpe/uhmwpeblends

Effect of Entangled State of Nascent UHMWPE on Structural and Mechanical Properties of HDPE/UHMWPE Blends

Rheological and Mechanical Properties of Ultrahigh Molecular Weight Polyethylene/high Density Polyethylene/polyethylene Glycol Blends

Ultra-high molecular weight polyethylene (UHMWPE)/high-density polyethylene (HDPE) blends with outstanding mechanical properties, wear resistance, and processability

Enhancing Gel Spinning of Ultra-High Molecular Weight Polyethylene: Insights into Rheology and Microstructure

Fibers of Ultra-High Molecular Weight Polyethylene Obtained by Gel Spinning with Polyalphaolefin Oil

Phase Morphology and Mechanical Properties of the Electrospun Polyoxymethylene/polyurethane Blend Fiber Mats

Morphology evolution and mechanical property enhancement of linear low‐density polyethylene by adding disentangled ultrahigh molecular weight polyethylene

IMPROVEMENT OF POLY(METHYL METHACRYLATE) ELECTROSPUN FIBER UNIFORMITY BY ADDITION OF POLY(ESTER AMINE)

Effects of Different Ultrahigh Molecular Weight Polyethylene Contents on the Formation and Evolution of Hierarchical Crystal Structure of High‐density Polyethylene/ultrahigh Molecular Weight Polyethylene Blend Fibers

PROGRESS IN ULTRA HIGH MOLECULAR WEIGHT POLYETHYLENE/POLYPYLENE BLENDS

A Comprehensive Review of Ultrahigh Molecular Weight Polyethylene Fibers for Applications Based on Their Different Preparation Techniques

Abrasive wear of HDPE/UHMWPE blends

Influence of sequential melting and sintering process on morphology development and performance properties of ultra‐high molecular weight polyethylene/low‐density polyethylene blends

Preparation of HDPE/UHMWPE/MMWPE Blends by Two-Step Processing Way and Properties of Blown Films

Thermal and Mechanical Properties of Ultra High Molecular Weight Polyethylene Fiber Reinforced High-Density Polyethylene Homocomposites: Effect of Processing Condition and Nanoclay Addition

Two‐stage Drawing Process to Prepare High‐strength and Porous Ultrahigh‐molecular‐weight Polyethylene Fibers: Cold Drawing and Hot Drawing

Effects of Maleic Anhydride Grafted Polyethylene on Rheological, Thermal, and Mechanical Properties of Ultra High Molecular Weight Polyethylene/Poly(Ethylene Glycol) Blends

Increasing the Resistance of HDPE to Abrasive Wear with Small Additions of UHMWPE

Dynamic Rheological Behavior of Hdpe/Uhmwpe Blends