Abstract:One low density polyethylene (LDPE) resin with high-speed extrusion coating property is fractionated through solvent gradient fractionation (SGF) technique using 1,2,4-trimethylbenzene (TMB) and ethyl cellosolve (ECS) as good/poor solvent pair at 115 °C. The pristine sample and its fractions are characterized by high-temperature gel permeation chromatography (HT-GPC) coupled with triple detectors (refractive index RI, light scattering LS, viscometer VIS), 13C–nuclear magnetic resonance spectroscopy (13C–NMR), differential scanning calorimetry (DSC) and successive self-nucleation/annealing (SSA) thermal fractionation. By adjusting the ratio of good/poor solvent, the obtained fractions show their molecular weight from 1.58 × 103 g/mol to 4.76 × 105 g/mol. It is found that the fractions with high molecular weight (fractions 10–13) occupy about 55.85% in resin. Particularly, the molecular weight distribution (MWD) of most fractions is in the range of 1.1–1.2. Each fraction contains more short chain branch (SCB) and less long chain branch (LCB) simultaneously. With increasing the molecular weight, the branching content shows no regular change. The lowest SCB and total branch content regions correspond to molecular weight 1.97 × 104 to 4.10 × 104 g/mol. The melting and crystallization temperatures of fractions firstly increase and then decrease with the molecular weight. The crystallinity decreases gradually from 51.7% to 31.1%. In the SSA thermal fractionation, each fraction shows a broad range of endotherm with multiple melting peaks in DSC curve corresponding to the different methylene sequence length (MSL) (Ln and Lw). The longest Ln (Lw) region occurs in the molecular weight of 8.95 × 103 to 3.14 × 104 g/mol. The relationship between chain microstructure and properties is also discussed.Graphical AbstractOne coating LDPE resin is effectively fractionated by solvent gradient fractionation using TMB/ECS as good/poor solvent pair according to molecular weight. The component with high molecular weight is more than that with low molecular weight. Higher molecular weight and LCB improve the melt strength synergetically, and suitable component with low molecular weight provides better flowability.

Effect of the Polyolefin Fraction Structure on the Morphology and Properties of Polymer Compositions Based on Ultrahigh Molecular Weight Polyethylene

Chain Structure and Mechanical Properties of Ethylene Copolymers in Two Operating Modes of Fluidized Bed Polymerization Reactor

Studies on composition and molecular structure of high impact polypropylene

Thermal and Mechanical Properties of Ultrahigh-Molecular-Weight Ethylene/1-Hexene Copolymers Prepared by Living Polymerization with Fluorinated Bis(Phenoxy-Imine) Titanium(Iv) Catalyst

Tuning the Mechanical Properties of Weakly Phase-Separated Olefin Block Copolymer by Establishing Co-Crystallization Structure with the Aid of Linear Polyethylene: the Dependence on Molecular Chain Length

Mechanical Properties and Crystallization Behavior of High Fluidity Polypropylene/metallocene Poly(ethylene–butene–hexene) Copolymer Blends

Studies on Comonomer Compositional Distribution of Poly(propylene Carbonate-Propylene Oxide) Copolymer and Its Effect on the Thermal, Mechanical and Oxygen Barrier Properties of Fractions

The Effect Of Comonomer Type And Content On The Properties Of Ziegler-Natta Bimodal High-Density Polyethylene

Morphology evolution and mechanical property enhancement of linear low‐density polyethylene by adding disentangled ultrahigh molecular weight polyethylene

Influence of organophilic montmorillonite and polypropylene on the rheological behaviors and mechanical properties of ultrahigh molecular weight polyethylene

Effect of the Structure on the Morphology and Spherulitic Growth Kinetics of Polyolefin In‐reactor Alloys

Study of Crystallization and Melting Behavior of Polypropylene‐block‐polyethylenes Copolymers Fractionated from Polypropylene and Polyethylene Mixtures

Enhanced Fracture Energy During Deformation Through the Construction of an Alternating Multilayered Structure for Polyolefin Blends

Influence of high molecular weight component on the hierarchical crystalline structures of injection‐molded bars of polyethylene

Microstructure characterization of one high-speed extrusion coating polyethylene resin fractionated by solvent gradient fractionation

Effect of Borpolymer on Mechanical and Structural Parameters of Ultra-High Molecular Weight Polyethylene

The effect of residual polymer structure on its several properties

Effect of Morphology on the Properties of High Density Polyethylene/Polyamide 6 Composite

Effect of Ethylene‐propylene Copolymer with Residual PE Crystallinity on Mechanical Properties and Morphology of PP/HDPE Blends

Structure-rheology properties of polyethylenes with varying macromolecular architectures

Crystallization Behavior of the Blends of Isotactic Polypropylene and Ethylene-Propylene Blocky Copolymers