Abstract:Introduction. Products containing WC-Co cemented tungsten carbides are commonly used in various industries. It is often operates at elevated temperatures, at which, as noted in the literature, tungsten carbides are susceptible to severe oxidation in air. However, no sufficiently accurate values of oxidation temperatures and dependence of these temperatures and the oxidation rate of tungsten carbides on the cobalt content with its wide variation have been established. The subject of the study is the oxidation process of WC-Co cemented tungsten carbides. The purpose of the work is to obtain the oxidation temperatures of WC-Co cemented tungsten carbides with different cobalt content by weight in the range of 3–20 %. Methods. The dynamics of oxidation was studied in air. Specimens of the same length were heated to a temperature of 850 °C and cooled at the same rate in the furnace of a push-rod dilatometer Netzsch 402 PC while its expansion was simultaneously recorded. The oxidation rate of the specimens was determined by the difference in its length before heating and after cooling. The values of oxidation temperatures were obtained by mathematical analysis of relationships of the expansion on temperature. Results and discussion. Experimental dependences of expansion of WC-Co cemented tungsten carbides on temperature in the range from 20 to 850 °C, and for WC-8Co – up to 1,150 °C, were obtained. The oxidation rate of WC-Co cemented tungsten carbides increased linearly with increasing concentration of tungsten carbides (decreased with increasing cobalt content). During heating, two characteristic temperatures were identified: the onset of oxidation (631±4 °C) and the transition to active oxidation (804±11 °C). The established temperatures were the same for different ratios of tungsten carbides and cobalt. The results can be used when choosing temperature conditions for products made from WC-Co cemented tungsten carbides.

Oxidation Behavior of Tungsten Carbide-6% Cobalt Cemented Carbide

Oxidation temperatures of WC-Co cemented tungsten carbides

Effect of High Temperature Annealing on the Microstructure and Thermal Shock Resistance of Tungsten Coatings Grown by Chemical Vapor Deposition

Oxidation behavior of in situ TiCp/Ti6Al4V composite with self-assembled network microstructure fabricated by reaction hot pressing

Effect of (Ti,W)C/TaC addition on the early oxidation behavior of surface layer of WC-Co cemented carbides

Oxidation behavior of the CVD-Al2O3 coatings on tungsten substrate at 1000 °C

Influences of Cr contents on oxidation behavior of WC-Co-Ni-Cr cemented carbides at 900 °C

Oxidation behavior of functionally graded cemented carbides with CoNiFeCr multi-principal-element alloy binder

Study on the oxidation of WC-Co cemented carbide under different conditions

Selective oxidation induced wear degradation in cemented carbides

Oxidative ablation behavior of W‐coated C/C composites prepared by CVD with heat‐treatment

Behaviors in Oxidation at 1100°C of an Equimolar CoNiFeMnCr High-Entropy Alloy and of its Versions Moderately Added with HfC or TaC Carbides

Microstructure and high-temperature oxidation behavior of Ti3AlC 2/W composites

Oxidative Ablation Behavior of W‐Coated C/C Composites Prepared by Chemical Vapor Deposition with Heat Treatment

Oxidation of SiC/BN/SiC ceramic matrix composites in dry and wet oxygen at intermediate temperatures

High-temperature oxidation behaviour of vacuum hot-pressed WC-15 wt% Al2O3 composites

Mechanism of the early stages of oxidation of WC–Co cemented carbides

Improvement of high-temperature oxidation resistance of WC–Co–Ni alloy by Cr3C2–CeO2–WS2 mixed additives and its mechanism

Fabrication of tungsten oxide powder from WC–Co cemented carbide scraps by oxidation behaviour

Oxidation Behavior of Ternary Carbide Ceramics in Hf–Al–C System in Air

Effect of Y2O3 Addition on High-Temperature Oxidation of Binderless Tungsten Carbide