Abstract:Coarse tungsten powders are usually used as raw material for preparing coarse grained WC-Co cemented carbides. Sodium can effectively promote the growth of tungsten powder during the reduction of tungsten oxide with hydrogen. Conventional addition of sodium salt into tungsten oxide powders by mechanical milling has the disadvantage of uneven distribution of sodium, which leads to abnormal growth of tungsten powders and affects the performance of WC-Co cemented carbides. In this study, uniform sodium doped ammonium paratungstate (APT) was prepared by adding sodium carbonate into ammonium tungstate solution during the evaporation and crystallization process based on the formation of ammonium-sodium paratungstate. Experimental results showed that sodium was uniformly distributed in the APT and promoted the growth of APT crystal. The sodium-doped APT was then used to produce coarse tungsten powders. Compared with tungsten powders obtained from tungsten trioxide with addition of sodium by mechanical milling, the coarse tungsten powders had larger average particle size and more uniform particle size distribution . The coarse tungsten powders were subsequently prepared into tungsten carbide powders and WC-Co cemented carbides by carburization and pressure sintering, respectively. Results showed that the obtained WC-Co cemented carbides had larger average WC grain size (6.8–7.2 μm), higher fracture toughness and transverse ruptures strength, and more uniform microstructure than that of WC-Co cemented carbides obtained by addition of sodium with mechanical milling. Moreover, sodium thoroughly volatilized during hydrogen reduction and carburization process, so that the purity of WC-Co cemented carbides was not reduced. Therefore, this study provided a new route for preparation of extra coarse-grained WC-Co cemented carbides.

The characteristics of WC based cemented carbide using nonmagnetic Ni(W) solid solution derived from ammonium paratungstate as the binder

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Ultrafine Binderless WC-based Cemented Carbides with Varied Amounts of AlN Nano-Powder Fabricated by Spark Plasma Sintering

WC-based cemented carbide with NiFeCrWMo high-entropy alloy binder as an alternative to cobalt

Preparation of low binder WC-Co-Ni cemented carbides with fine WC grains and homogeneous distribution of Co/Ni

Study on Effect of High-Entropy Alloy Binder on Microstructure and Properties of WC Cemented Carbide Doped with Rare Earth Oxide

The Effect of Carbon Content on the Microstructure and Mechanical Properties of Cemented Carbides with a CoNiFeCr High Entropy Alloy Binder

Ultrafine WC-Ni cemented carbides fabricated by spark plasma sintering

Preparation of Ultra-Fine WC-Co Cermet and Its Wear Behavior

Microstructures and Properties of a Novel Cemented Carbide Prepared Using a Co–Ni–Cu Multiprincipal Element Alloy As the Binder

Insight into Grain Refinement Mechanisms of WC Cemented Carbide with Al0.5CoCrFeNiTi0.5 Binder

High-performance WC-AlCoCrFeNi 2.1 cemented carbides fabricated by resistance seam additive manufacturing

Extraordinary High-Temperature Mechanical Properties in Binder-Free Nanopolycrystalline WC Ceramic

The effect of binder phase content on WC-AlCoCrFeNiTi0.2 high entropy cemented carbides microstructure and mechanical properties

Effect of WC grain size on mechanical properties and microstructures of cemented carbide with medium entropy alloy Co-Ni-Fe binder

Preparation of extra coarse-grained WC-Co cemented carbides by doping sodium in the ammonium tungstate solution during evaporation crystallization process

Effect of binder content and sintering time on the microstructure and mechanical properties of gradient cemented carbides with Ni binder

Synthesis of Nanostructured Tungsten Carbide (WC) from Ammonia Paratungstate-APT and its Characterization by XRD and Rietveld Refinement

Strengthening and toughening of WC-Ni alloys by adding novel (Ti, Hf, Ta, Nb, Zr)(C, N) high entropy powder

WC-Based Cemented Carbides with High Entropy Alloyed Binders: A Review

Effect of Nano-AlN Addition on the Microstructure and Mechanical Properties of Binderless WC-VC-TaC-AlN Cemented Carbides