Abstract:The metallic interconnects are essential components of energy devices such as fuel cells and electrolysis cells, batteries, as well as electronics and optoelectronic devices. In recent years, 3D printing processes have offered complementary routes to the conventional photolithography- and vacuum-based processes for interconnect fabrication. Among these methods, the confined electrodeposition (CED) process has enabled a great control over the microstructure of the printed metal, direct printing of high electrical conductivity (close to the bulk values) metals on flexible substrates without a need to sintering, printing alloys with controlled composition, printing functional metals for various applications including magnetic applications, and for in situ scanning electron microscope (SEM) nanomechanical experiments. However, the metal deposition rate (or the overall printing speed) of this process is reasonably slow because of the chemical nature of the process. Here, we propose using the CED process to print a single layer of a metallic trace as the seed layer for the subsequent selected-area electroless plating. By controlling the activation sites through printing by the CED process, we control, where the metal grows by electroless plating, and demonstrate the fabrication of complex thin-film patterns. Our results show that this combined process improves the processing time by more than 2 orders of magnitude compared to the layer-by-layer printing process by CED. Additionally, we obtained Cu and Ni films with an electrical resistivity as low as ∼1.3 and ∼2 times of the bulk Cu and Ni, respectively, without any thermal annealing. Furthermore, our quantitative experiments show that the obtained films exhibit mechanical properties close to the bulk metals with an excellent adhesion to the substrate. We demonstrate potential applications for radio frequency identification (RFID) tags, for complex printed circuit board patterns, and resistive sensors in a Petri dish for potential biological applications.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.1c01890?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.1c01890</a>.SEM images of the single-layer printed Cu and Ni lines with a nozzle diameter of ∼250 μm for different nozzle speeds; The optical images of single-layer Cu and Ni lines printed with different nozzle speeds, and the width and thickness of the printed Cu and Ni lines vs the nozzle speed; The FIB-sectioned cross-sectional images of Cu and Ni films; and The schematic of an unpinned (top) and pinned (bottom) indentation-induced buckle (<a class="ext-link" href="/doi/suppl/10.1021/acsami.1c01890/suppl_file/am1c01890_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Trench Wiring Process Applying Electroless Nickel Plating for Fine and High-Aspect-Ratio Pattern

Composite electroplating to enhance the GMI output stability of melt-extracted wires

Development of electro-copper plating with nanodiamonds for electronic interconnects in advanced packaging

Fabrication of High Aspect Ratio Through-Wafer Copper Interconnects by Reverse Pulse Electroplating

8-inch wafer-level electroplating of nanotwinned copper redistribution layer for advanced packaging

Silicon Micromachining Of High Aspect Ratio, High-Density Through-Wafer Electrical Interconnects For 3-D Multichip Packaging

Electrochemical mechanism of layout-dependent corrosion of tungsten in contact plugs

Copper Filling Process for Small Diameter, High Aspect Ratio Through Silicon Via (Tsv)

Fabrication of Anodic Aluminum Oxide Template and Cu Nanowire Surface Fastener

Fast copper plating process for TSV fill

Cu electroplating chemistry and process enabling rapid TSV filling with long bath life

Copper electroplating technology for microvia filling

Growth and Branching Mechanisms of Electrochemically Self-Organized Mesoscale Metallic Wires

Wet processes deposition for HAR TSV metallization using electroless Co liner and alkaline Cu seed layer

Improved Electrochemical Plating for Void-Free Copper Line in ULSI Interconnect

Electroplating Cu on ALD TiN for high aspect ratio TSV

Completely Filling of Through-Silicon-Vias with High Aspect Ratio by High Cavity Physical Vapor Deposition and Electroplating

Interconnect Fabrication by Electroless Plating on 3D-Printed Electroplated Patterns

Moving Boundary Simulation and Experimental Verification of High Aspect-Ratio Through-Silicon-Vias for 3-D Integration

All-wet TSV filling with highly adhesive displacement plated Cu seed layer

High Aspect Ratio Copper Through-Silicon-vias for 3D Integration