Abstract:The limited availability of Te poses challenges for the widespread application of Bi2Te3-based thermoelectric modules. In this work, we explored the thermoelectric module potential of Te-free PbSe by elevating its power factor through crystal growth and slight-tuning vacancy and interstitial defects. The outcomes revealed a gradual increase in the carrier concentration and a high room-temperature carrier mobility of similar to 1750 cm(2) V-1 s(-1), leading to an enhanced power factor of similar to 37.4 mu W cm(-1) K-2 in Pb1.006Se+0.0016 Al crystals. We grew PbSe crystals to minimize the impact of grain boundaries on the charge carrier transport. Subsequently, n-type PbSe crystals were produced by introducing extra Pb to occupy the intrinsic Pb vacancies, effectively minimizing vacancy scattering. Following this, a minute quantity of small-sized Al (<= 2 parts per thousand) was introduced, revealing that these surplus Al atoms served as cationic dopants, substituting for Pb, while also occupying interstitial positions. The interstitial doping increases the carrier concentration while maintaining carrier mobility due to the distinct dimensions between the interstitial atoms and mean free path of electrons. The consistently improved power factor with the suppression of thermal conductivity brings about a significantly high ZT value over the whole temperature. Specifically, the ZT values of the Pb1.006Se+0.0016Al crystal reached similar to 0.5 at 300 K, similar to 1.5 at 673 K, and the average ZT (ZT(ave)) reached similar to 1.1 at 300-773 K. Ultimately, a single-leg power generation efficiency similar to 7.1% was achieved in Pb1.006Se+0.0016Al crystal and a 7-pair module reached a maximum temperature cooling difference similar to 51.2 K at the high temperature side T-h of 363 K. These results indicate the potential for developing a cost-effective and high-performance thermoelectric module utilizing PbSe.

Realizing high-efficiency power generation in low-cost PbS-based thermoelectric materials

Realizing High Energy Conversion Efficiency in a Novel Segmented‐Mg3(Sb, Bi)2/Cubic‐GeTe Thermoelectric Module for Power Generation

Numerical Modeling and Optimization of the Segmented PbTe–BiTe-based Thermoelectric Leg

Realizing an excellent conversion efficiency of 14.5% in the Mg 3 Sb 2 /GeTe-based thermoelectric module for waste heat recovery

Realizing a Superior Conversion Efficiency of ≈11.3% in the Group IV-VI Thermoelectric Module

Realizing thermoelectric cooling and power generation in N-type PbS0.6Se0.4 via lattice plainification and interstitial doping

Realizing ultrahigh ZT value and efficiency of the Bi2Te3 thermoelectric module by periodic heating

Realizing High-Performance Thermoelectric Modules Through Enhancing the Power Factor Via Optimizing the Carrier Mobility in N-Type PbSe Crystals

All‐Mg3Sb2‐Based Module for Thermoelectric Power Generation

Design and Fabrication of Segmented GeTe/(Bi,Sb)2Te3 Thermoelectric Module with Enhanced Conversion Efficiency

High efficiency GeTe-based materials and modules for thermoelectric power generation

Realizing high-performance thermoelectric module through enhancing power factor via optimizing carrier mobility in n-type PbSe crystals

High Performance Thermoelectrics from Earth-Abundant Materials: Enhanced Figure of Merit in Pbs Through Nanostructuring Grain Size

High‐Efficiency Thermoelectric Module Based on High‐Performance Bi0.42Sb1.58Te3 Materials

A record thermoelectric efficiency in tellurium-free modules for low-grade waste heat recovery

Designing good compatibility factor in segmented Bi0.5Sb1.5Te3 – GeTe thermoelectrics for high power conversion efficiency

A high-efficiency GeTe-based thermoelectric module for low-grade heat recovery

Bi2Te3-Based Thermoelectric Modules for Efficient and Reliable Low-Grade Heat Recovery

Realization of Valence Band Convergence for High Thermoelectric Performance P-Type PbS

PbSe Thermoelectrics: Efficient Candidates for Power Generation and Cooling

Realizing high-ranged thermoelectric performance in PbSnS2 crystals