Abstract:Thermoelectric materials have a wide range of application because they can be directly used in refrigeration and power generation. And the Bi2Te3 stand out because of its excellent thermoelectric performance and are used in commercial thermoelectric devices. However, n-type Bi2Te3 has seriously hindered the development of Bi2Te3-based thermoelectric devices due to its weak mechanical properties and inferior thermoelectric performance. Therefore, it is urgent to develop a high-performance n-type Bi2Te3 polycrystalline. In this work, we employed interstitial Cu and the hot deformation process to optimize the thermoelectric properties of Bi2Te2.7Se0.3, and a high-performance thermoelectric module was fabricated based on this material. Our combined theoretical and experimental effort indicates that the interstitial Cu reduce the defect density in the matrix and suppresses the donor-like effect, leading to a lattice plainification effect in the material. In addition, the two-step hot deformation process significantly improves the preferred orientation of the material and boosts the mobility. As a result, a maximum ZT of 1.27 at 373 K and a remarkable high ZTave of 1.22 across the temperature range of 300−425 K are obtained. The TEG (7-pair) and TEC (127-pair) modules were fabricated with our n-type textured Cu0.01Bi2Te2.7Se0.3 coupled with commercial p-type Bi2Te3. The TEC module demonstrates superior cooling efficiency compared to the commercial Bi2Te3 device, achieving a ΔT of 65 and 83.4 K when the hot end temperature at 300 and 350 K, respectively. In addition, the TEG module attains an impressive conversion efficiency of 6.5% at a ΔT of 225 K, which is almost the highest value among the reported Bi2Te3-based TEG modules.

A record thermoelectric efficiency in tellurium-free modules for low-grade waste heat recovery

Towards Tellurium-Free Thermoelectric Modules for Power Generation from Low-Grade Heat.

Bi2Te3-Based Thermoelectric Modules for Efficient and Reliable Low-Grade Heat Recovery

High Thermoelectric Performance of a Sc2Si2Te6 Monolayer at Medium Temperatures: an Ab Initio Study.

High‐Efficiency Thermoelectric Module Based on High‐Performance Bi0.42Sb1.58Te3 Materials

Realizing an Excellent Conversion Efficiency of 14.5% in the Mg3Sb2/GeTe-based Thermoelectric Module for Waste Heat Recovery

An over 10% module efficiency obtained using non-Bi 2 Te 3 thermoelectric materials for recovering heat of <600 K

A high-efficiency GeTe-based thermoelectric module for low-grade heat recovery

Lead-free and scalable GeTe-based thermoelectric module with an efficiency of 12%

Realizing an excellent conversion efficiency of 14.5% in the Mg 3 Sb 2 /GeTe-based thermoelectric module for waste heat recovery

Interfacial Design Contributing to High Conversion Efficiency in Mg3(Sb, Bi)2/Bi2Te3 Thermoelectric Module with Superior Stability

High Performance Dual-mode Module for Power Generation and Cooling Based on Optimized BiSbTe

All‐Mg3Sb2‐Based Module for Thermoelectric Power Generation

Realizing Ultrahigh Conversion Efficiency of ≈9.0% in YbCd2Sb2/Mg3Sb2 Zintl Module for Thermoelectric Power Generation

Bismuth Telluride Based Efficient Thermoelectric Power Generator with Electrically Conducive Interfaces for Harvesting Low Temperature Heat

Realizing High-Efficiency Thermoelectric Module by Suppressing Donor-Like Effect and Improving Preferred Orientation in N-Type Bi2(Te, Se)3

Realizing ultrahigh ZT value and efficiency of the Bi2Te3 thermoelectric module by periodic heating

Performance boost for bismuth telluride thermoelectric generator via barrier layer based on low Young's modulus and particle sliding

Performance Boost for Bismuth Telluride Thermoelectric Generator Via Barrier Layer Based on Low Young’s Modulus and Particle Sliding

Thermoelectric Generator Using Low-Cost Thermoelectric Modules for Low-Temperature Waste Heat Recovery

High-performance Sb2Si2Te6 thermoelectric device