Mucus models to evaluate nanomedicines for diffusion.

A. Groo,F. Lagarce

DOI: https://doi.org/10.1016/j.drudis.2014.01.011

IF: 8.369

2014-08-01

Drug Discovery Today

Abstract:

What problem does this paper attempt to address?

High efficiency GeTe-based materials and modules for thermoelectric power generation

Tong Xing,Qingfeng Song,Pengfei Qiu,Qihao Zhang,Ming Gu,Xugui Xia,Jincheng Liao,Xun Shi,Lidong Chen

DOI: https://doi.org/10.1039/d0ee02791j

2021-01-01

Abstract:A GeTe-based TE module with a high energy conversion efficiency of 7.8% under Δ T = 500 K is fabricated.

energy & fuels,chemistry, multidisciplinary,engineering, chemical,environmental sciences
High thermoelectric performance in GeTe with compositional insensitivity

Jinfeng Dong,Yilin Jiang,Jiawei Liu,Jun Pei,Xian Yi Tan,Haihua Hu,Ady Suwardi,Ning Jia,Chuntai Liu,Qiang Zhu,Qingyu Yan,Jing-Feng Li

DOI: https://doi.org/10.1016/j.nanoen.2022.107809

IF: 17.6

2022-09-22

Nano Energy

Abstract:Thermoelectric materials have obtained worldwide attention as they are attractive for waste heat recovery and solid-state cooling. However, their performance is usually sensitive to material compositions, which is less favorable for industrial applications. In this work, we developed composition-insensitive GeTe-based compounds ((100- x - y )%GeTe- x %CuBiSe 2 - y %PbTe, CBS x -Pb y ) with high ZT max as well as ZT ave values. The compositional insensitivity can be associated with the persistently high quality factors across the range of compositions. This is largely due to the interplay between electrical and thermal transport caused by the synergy of CuBiSe 2 and PbTe alloying. CuBiSe 2 alloying can effectively tune the carrier concentrations, while PbTe alloying can significantly decrease the thermal conductivity at a minor sacrifice of electrical properties. The combined effects of CuBiSe 2 and PbTe alloying lead to high carrier mobility of 60 cm 2 V −1 s −1 and low thermal conductivities for CBS x -Pb y samples simultaneously. Consequently, high ZT ave values of 1.4–1.5 in the temperature range of 400 K and 773 K for broad compositions (CBS3-Pb y , y = 2 – 8 and CBS x -Pb6, x = 2 – 5) are achieved. A single-leg module is also fabricated, which shows a high power density of 1.46 W/cm 2 and an excellent efficiency of 13.4%. The high ZT ave with compositional insensitivity and the outstanding module performance demonstrate the promising large-scale application of the developed GeTe-based compositions.

materials science, multidisciplinary,chemistry, physical,physics, applied,nanoscience & nanotechnology
Lead-free and scalable GeTe-based thermoelectric module with an efficiency of 12%

Li Xie,Chen Ming,Qingfeng Song,Chao Wang,Jincheng Liao,Lei Wang,Chenxi Zhu,Fangfang Xu,Yi-Yang Sun,Shengqiang Bai,Lidong Chen

DOI: https://doi.org/10.1126/sciadv.adg7919

IF: 13.6

2023-07-06

Science Advances

Abstract:GeTe-based materials with superior thermoelectric properties promise great potential for waste heat recovery. However, the lack of appropriate diffusion barrier materials (DBMs) limits not only the energy conversion efficiency but also the service reliability of the thermoelectric devices. Here, we propose a design strategy based on phase equilibria diagrams from first-principles calculations and identify transition metal germanides (e.g., NiGe and FeGe 2 ) as the DBMs. Our validation experiment confirms the excellent chemical and mechanical stabilities of the interfaces between the germanides and GeTe. We also develop a process for scaling up the GeTe production. Combining with module geometry optimization, we fabricate an eight-pair module using mass-produced p-type Ge 0.89 Cu 0.06 Sb 0.08 Te and n-type Yb 0.3 Co 4 Sb 12 and achieve a record-high efficiency of 12% among all reported single-stage thermoelectric modules. Our work thus paves the way for waste heat recovery based on completely lead-free thermoelectric technology.

multidisciplinary sciences
Multiphase Coherent Nanointerface Network Enhances Thermoelectric Performance for Efficient Energy Conversion and Contactless Thermosensation Applications in GeTe

Jianglong Zhu,Xiaobo Tan,Min Hong,Yanxing Wei,Huangshui Ma,Fan Feng,Yuange Luo,Hao Wu,Qiang Sun,Ran Ang

DOI: https://doi.org/10.1002/aenm.202402552

IF: 27.8

2024-07-20

Advanced Energy Materials

Abstract:A novel multiphase coherent nanointerface network is constructed in Cu2Te alloyed Ge0.84Cd0.06Pb0.10Te, facilitating high‐range thermoelectric performance and robust mechanical properties for energy conversion and contactless thermosensation applications. Counter doping is a prevalent strategy to optimize the excessively high carrier concentration in GeTe, while it may impair carrier transport and reduce mobility, thereby limiting the potential to improve ZT. Herein, a novel approach to overcome this challenge is proposed. A multiphase coherent nanointerface network, formed between pseudo‐cubic GeTe, Cu2Te, and PbTe phases, with effective Cu ions delocalization, has been realized in Cu2Te alloyed Ge0.84Cd0.06Pb0.10Te. This design selectively modulates both charge carrier and phonon transport, resulting in increased mobility and optimized carrier concentration that contribute to enhanced power factor, with an ultra‐low lattice thermal conductivity of ≈0.33 W m−1 K−1 at 653 K. Consequently, the peak ZT of ≈2.22 at 803 K and average ZT of ≈1.40 from 303 to 803 K is achieved in (Ge0.84Cd0.06Pb0.10Te)0.99(Cu2Te)0.01. Furthermore, the novel structural modulation results in robust mechanical properties. Utilizing these optimized materials, achieving a high power density of ≈1.47 W cm−2 at a temperature difference of 400 K in the fabricated 7‐pair thermoelectric module. Moreover, a thermoelectric energy harvesting array device is assembled, exhibiting potential for applications in non‐radiative energy harvesting from lasers and touchless thermosensation, further advancing the applications of thermoelectric materials and devices.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,energy & fuels
Design and Fabrication of Segmented GeTe/(Bi,Sb)2Te3 Thermoelectric Module with Enhanced Conversion Efficiency

Jun Pei,Jian‐Lei Shi,Hezhang Li,Yilin Jiang,Jinfeng Dong,Hua‐Lu Zhuang,Bowen Cai,Bin Su,Jincheng Yu,Wei Zhou,Bo‐Ping Zhang,Jing‐Feng Li

DOI: https://doi.org/10.1002/adfm.202214771

IF: 19

2023-02-25

Advanced Functional Materials

Abstract:GeTe/(Bi,Sb)2Te3 segmented one‐leg thermoelectric modules are successfully designed and fabricated. Its maximum efficiency reaches 9.5 % under the adiabatic boundary condition of cold side heat flow via Mini‐PEM, indicating a good application prospect. GeTe and (Bi,Sb)2Te3 are two representative thermoelectric (TE) materials showing maximum performance at middle and low temperature, respectively. In order to achieve higher performance over the whole temperature range, their segmented one‐leg TE modules are designed and fabricated by one‐step spark plasma sintering (SPS). To search for contact and connect layers, the diffusion behavior of Fe, Ni, Cu, and Ti metal layers in GeTe is studied systematically. The results show that Ti with a similar linear expansivity (10.80 × 10−6 K−1) to GeTe, has low contact resistance (3 μΩ cm2) and thin diffusion layer (0.4 μm), and thus is an effective metallization layer for GeTe. The geometric structure of the GeTe/(Bi,Sb)2Te3 segmented one‐leg TE module and the ratio of GeTe to (Bi,Sb)2Te3 are determined by finite element simulation method. When the GeTe height ratio is 0.66, its theoretical maximum conversion efficiency (ηmax) can reach 15.9% without considering the thermal radiation and thermal/electrical contact resistance. The fabricated GeTe/(Bi,Sb)2Te3 segmented one‐leg TE module showed a ηmax up to 9.5% with a power density ≈ 7.45 mW mm−2, which are relatively high but lower than theoretical predictions, indicating that developing segmented TE modules is an effective approach to enhance TE conversion efficiency.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Modifying Roles of CuSbSe2 in Realizing High Thermoelectric Performance of GeTe

Yang Jin,Yuting Qiu,Shulin Bai,Hongyao Xie,Shibo Liu,Tao Hong,Xiang Gao,Yi Wen,Li-Dong Zhao

DOI: https://doi.org/10.1002/aenm.202400623

IF: 27.8

2024-01-01

Advanced Energy Materials

Abstract:Thermoelectric materials are widely researched for their energy conversion capabilities in the fields of power generation and refrigeration. And a superior thermoelectric conversion efficiency requires an excellent power factor and low thermal conductivity. Herein, a remarkable thermoelectric figure of merit(ZT) similar to 2.6 at 673 K is realized in GeTe with 20% addition of CuSbSe2. Multiple synergistic effects of CuSbSe2 alloying collectively contribute to the excellent thermoelectric performance in GeTe. CuSbSe2 alloying effectively tunes ultrahigh carrier density of GeTe to the optimum. The introduction of Cu, Sb, and Se atoms create numerous point defects that scatter high-frequency phonons. Additionally, surplus CuSbSe2 facilitates the formation of copper-selenium phases, which embed at grain boundaries and generate interfaces after sintering. Combining the planar defects evolved from Ge vacancies, multi-dimension defects effectively scatter multiple frequency phonons. An extraordinarily low lattice thermal conductivity of 0.3 Wm(-1) K-1 at 673 K is obtained, approaching the theoretical estimation predicted by Cahill model. Eventually, the peak conversion efficiency of 7.4% is obtained in segmented device with Delta T of 419 K. The commingled effects of CuSbSe2 in GeTe further open up an elitist route to designing high-performance materials.
Realizing an excellent conversion efficiency of 14.5% in the Mg 3 Sb 2 /GeTe-based thermoelectric module for waste heat recovery

Xiaofang Li,Chen Chen,Li Yin,Xinyu Wang,Jun Mao,Feng Cao,Qian Zhang

DOI: https://doi.org/10.1039/d3ee02587j

IF: 32.5

2023-01-01

Energy & Environmental Science

Abstract:The single-stage module of Mg 3.15 Co 0.05 Sb 1.24 Bi 0.75 Se 0.01 /(Pb 0.15 Ge 0.85 Te) 0.8 (AgSbTe 2 ) 0.2 realized a remarkable conversion efficiency of 14.5% at a temperature difference of 480 K.

energy & fuels,chemistry, multidisciplinary,engineering, chemical,environmental sciences
Realizing High-Efficiency Thermoelectric Module by Suppressing Donor-Like Effect and Improving Preferred Orientation in N-Type Bi2(Te, Se)3

Yichen Li,Shulin Bai,Yi Wen,Zhe Zhao,Lei Wang,Shibo Liu,Junqing Zheng,Siqi Wang,Shan Liu,Dezheng Gao,Dongrui Liu,Yingcai Zhu,Qian Cao,Xiang Gao,Hongyao Xie,Li-Dong Zhao

DOI: https://doi.org/10.1016/j.scib.2024.04.034

IF: 18.9

2024-01-01

Science Bulletin

Abstract:Thermoelectric materials have a wide range of application because they can be directly used in refrigeration and power generation. And the Bi2Te3 stand out because of its excellent thermoelectric performance and are used in commercial thermoelectric devices. However, n-type Bi2Te3 has seriously hindered the development of Bi2Te3-based thermoelectric devices due to its weak mechanical properties and inferior thermoelectric performance. Therefore, it is urgent to develop a high-performance n-type Bi2Te3 polycrystalline. In this work, we employed interstitial Cu and the hot deformation process to optimize the thermoelectric properties of Bi2Te2.7Se0.3, and a high-performance thermoelectric module was fabricated based on this material. Our combined theoretical and experimental effort indicates that the interstitial Cu reduce the defect density in the matrix and suppresses the donor-like effect, leading to a lattice plainification effect in the material. In addition, the two-step hot deformation process significantly improves the preferred orientation of the material and boosts the mobility. As a result, a maximum ZT of 1.27 at 373 K and a remarkable high ZTave of 1.22 across the temperature range of 300−425 K are obtained. The TEG (7-pair) and TEC (127-pair) modules were fabricated with our n-type textured Cu0.01Bi2Te2.7Se0.3 coupled with commercial p-type Bi2Te3. The TEC module demonstrates superior cooling efficiency compared to the commercial Bi2Te3 device, achieving a ΔT of 65 and 83.4 K when the hot end temperature at 300 and 350 K, respectively. In addition, the TEG module attains an impressive conversion efficiency of 6.5% at a ΔT of 225 K, which is almost the highest value among the reported Bi2Te3-based TEG modules.
High‐Efficiency Thermoelectric Module Based on High‐Performance Bi0.42Sb1.58Te3 Materials

Gang Wu,Qiang Zhang,Yuntian Fu,Xiaojian Tan,Jacques G. Noudem,Zongwei Zhang,Chen Cui,Peng Sun,Haoyang Hu,Jiehua Wu,Guo‐Qiang Liu,Jun Jiang

DOI: https://doi.org/10.1002/adfm.202305686

IF: 19

2023-08-06

Advanced Functional Materials

Abstract:Ag5SbSe4 doping not only enhances the average power factor of Bi0.42Sb1.58Te3 by improved density‐of‐states effective mass, but also reduces the lattice thermal conductivity by induced multiscale defects. Consequently, a peak ZT of 1.40 at 375 K and a conversion efficiency of 6.5% is achieved at ΔT = 200 K, which is better than most of previously reported results. Bismuth‐telluride‐based alloy is the sole thermoelectric candidate for commercial thermoelectric application in low‐grade waste heat harvest near room temperature, but the sharp drop of thermoelectric properties at higher temperature and weak mechanical strength in zone‐melted material are the main obstacles to its wide development for power generation. Herein, an effective approach is reported to improve the thermoelectric performance of p‐type Bi0.42Sb1.58Te3 hot‐pressed sample by incorporating Ag5SbSe4. A peak ZT of 1.40 at 375 K and a high average ZT of 1.25 between 300 and 500 K are achieved. Such outstanding thermoelectric performance originates from the synergistic effects of improved density‐of‐states effective mass, reduced bipolar thermal conductivity by the boosted carrier concentration, and suppressed lattice thermal conductivity by the induced phonon scattering centers including substitute point defects, dislocations, stress–strain clusters, and grain boundaries. Comprised of the p‐type Bi0.42Sb1.58Te3 + 0.10 wt% Ag5SbSe4 and zone‐melted n‐type Bi2Te2.7Se0.3, the thermoelectric module exhibits a high conversion efficiency of 6.5% at a temperature gradient of 200 K, indicating promising applications for low‐grade heat harvest near room temperature.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
High‐Performance Industrial‐Grade p‐Type (Bi,Sb)2Te3 Thermoelectric Enabled by a Stepwise Optimization Strategy

Qiang Zhang,Minhui Yuan,Kaikai Pang,Yuyou Zhang,Ruoyu Wang,Xiaojian Tan,Gang Wu,Haoyang Hu,Jiehua Wu,Peng Sun,Guo‐Qiang Liu,Jun Jiang

DOI: https://doi.org/10.1002/adma.202300338

IF: 29.4

2023-03-04

Advanced Materials

Abstract:As the sole dominator of the commercial thermoelectric (TE) market, Bi2Te3‐based alloys play an irreplaceable role in Peltier cooling and low‐grade waste heat recovery. At present, the main barrier to a wider application is the relatively low efficiency determined by the low‐rise TE figure of merit ZT. Herein, an effective approach is reported for improving the TE performance of p‐type (Bi,Sb)2Te3 by incorporating Ag8GeTe6 and Se. Specifically, the diffused Ag and Ge atoms into the matrix conduce to optimized carrier concentration and enlarged the density of states effective mass while the Sb‐rich nanoprecipitates generate coherent interfaces with little loss of carrier mobility. The subsequent Se dopants introduce multiple phonon scattering sources and significantly suppress the lattice thermal conductivity while maintaining a decent power factor. Consequently, a high peak ZT of 1.53 at 350 K and a remarkable average ZT of 1.31 (300−500 K) are attained in the Bi0.4Sb1.6Te0.95Se0.05 + 0.10 wt% Ag8GeTe6 sample. Most noteworthily, the size and mass of the optimal sample have been enlarged to Ø40 mm‐200 g and the constructed 17‐couple TE module exhibits an extraordinary conversion efficiency η of 6.3% at ΔT = 245 K. This work demonstrates a facile method to develop high‐performance and industrial‐grade (Bi,Sb)2Te3‐based alloys, which paves a strong way for the further practical applications. This article is protected by copyright. All rights reserved

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Realizing High Energy Conversion Efficiency in a Novel Segmented‐Mg3(Sb, Bi)2/Cubic‐GeTe Thermoelectric Module for Power Generation

Congcong Xu,Zhongxin Liang,Wuyang Ren,Shaowei Song,Fanghao Zhang,Zhifeng Ren

DOI: https://doi.org/10.1002/aenm.202202392

IF: 27.8

2022-10-07

Advanced Energy Materials

Abstract:This study develops a novel thermoelectric power generation module based on segmented‐Mg3(Sb, Bi)2 and cubic‐GeTe from the perspective of structural optimization. The segmented module shows good energy conversion efficiency and output power, which broadens the potential candidate material library for segmented thermoelectric devices. The performance of thermoelectric materials has been improved considerably in recent decades, making the concept of generating energy from waste heat via solid‐state thermoelectric devices more realistic. The construction of multi‐stage modular structures based on complex parameter optimization to maximize the efficiency of each material over its optimal operating temperature range has become an effective strategy for improving device performance. Here, multi‐segmented n‐type Mg3(Sb, Bi)2 with low‐contact‐resistance buffer layers is first fabricated, and phase‐transition‐suppressed cubic p‐type GeTe with enhanced thermoelectric performance is subsequently designed to match the segmented n‐type legs. A 3D finite‐element analysis model is then used to optimize the module size, providing higher energy conversion efficiency with an optimal average figure of merit over the entire operating temperature range. As a result, the prepared segmented‐Mg3(Sb, Bi)2/cubic‐GeTe module exhibits a high conversion efficiency of (12.8 ± 0.8)% at a hot‐side temperature of 773 K with a temperature difference of ≈480 K, which is also comparable to that of previously reported thermoelectric modules. This study increases the number of matching combinations among n‐/p‐type thermoelectric materials and further broadens the potential candidate material library for segmented thermoelectric devices.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,energy & fuels
Interface and Surface Engineering Realized High Efficiency of 13% and Improved Thermal Stability in Mg3Sb1.5Bi0.5‐Based Thermoelectric Generation Devices

Xinzhi Wu,Yangjian Lin,Zhijia Han,Huan Li,Chengyan Liu,Yupeng Wang,Pengxiang Zhang,Kang Zhu,Feng Jiang,Jian Huang,Haohan Fan,Feng Cheng,Binghui Ge,Weishu Liu

DOI: https://doi.org/10.1002/aenm.202203039

IF: 27.8

2022-11-07

Advanced Energy Materials

Abstract:A high conversion efficiency (η) of 13% was achieved with a hot‐side temperature (Th) of 500 °C and cold‐side temperature (Tc) of about 5 °C. The thermoelectric device showed a stable η of over 100 h at Th and Tc of 400 and 5 °C, respectively. Realizing high‐temperature thermal stability in thermoelectric (TE) generators is a critical challenge. In this study, a synergistic interface and surface optimization strategy is implemented to enhance Mg3Sb1.5Bi0.5 TE generator performance by employing FeCrTiMnMg thermoelectric interface materials and the MgMn‐based alloy protective coating. The competitive output power density (ω) of 1.7 W cm−2 and a conversion efficiency (η) of 13% for the single‐leg device are achieved at hot‐side temperature (Th) and cold‐side temperature (Tc) of 500 and 5 °C, respectively. An ω of 0.8 W cm−2 and η of 6% for the two‐couple TE devices with p‐type commercial Bi2Te3 are also realized, values that are competitive with the commercial Bi2Te3 device. Additionally, the single‐leg device shows a high stable η for over 100 h when the Th and Tc are 400 and 5 °C, respectively, with an change rate (Δηmax/ηmax,o) of <3%. In situ transmission electron microscopy analysis further reveals that the high stability results from the effectively sluggish interdiffusion and reduced Mg evaporation that decrease the chemical potential gradient, reduce the saturated vapor pressure, and increase the diffusion activation energy barrier. This study provides a general technique route for boosting the high‐temperature thermal stability of TE generator.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,energy & fuels
Enhancing thermoelectric performance in GeTe through Ge enrichment regulation and AgCuTe alloying

Jingyi Lyu,Jingfeng Li,Wenwei Yang,Zhixing Chen,Zijie Ren,Zhanpeng Zhao,Shenghua Liu,Jing Shuai

DOI: https://doi.org/10.1016/j.cej.2024.149695

IF: 15.1

2024-02-22

Chemical Engineering Journal

Abstract:Germanium telluride (GeTe) exhibits substantial potential as a thermoelectric material well-suited for mid-temperature applications. The presence of a significant amount of off-stoichiometric Ge leads to the formation of Ge precipitates and vacancies, which exert a pronounced influence on the electrical and thermal transport properties of GeTe. In this study, a heat treatment process is initially applied to alleviate Ge enrichment within pristine GeTe, resulting in the achievement of a uniform distribution of Ge precipitates throughout the matrix. Subsequently, we coarsely optimize the carrier concentration through Bi counter-doping, thereby attaining the desired range for optimal performance. Notably, we finely adjust the Ge/Te ratio through AgCuTe alloying, effectively modulating Ge precipitation, reducing lattice thermal conductivity, and enhancing the thermoelectric performance of GeTe. Consequently, the synthesized sample (Ge 0.94 Bi 0.06 Te) 0.98 (AgCuTe) 0.02 exhibits a peak ZT value of approximately 2.27 at 773 K, with an average ZT value of approximately 1.38 within the temperature range of 323 to 773 K, making this material as a prominent candidate for medium-temperature thermoelectric applications.

engineering, chemical, environmental
Hierarchical Architectural Structures Induce High Performance in n‐Type GeTe‐Based Thermoelectrics

De‐Zhuang Wang,Wei‐Di Liu,Meng Li,Kun Zheng,Hanwen Hu,Liang‐Cao Yin,Yifeng Wang,He Zhu,Xiao‐Lei Shi,Xiaoning Yang,Qingfeng Liu,Zhi‐Gang Chen

DOI: https://doi.org/10.1002/adfm.202213040

IF: 19

2023-01-07

Advanced Functional Materials

Abstract:By proper structure engineering, exotic n‐type GeTe‐based materials with hierarchical architectural structures are reported. This unique architecture can simultaneously increase electrical performance and decrease thermal performance, and demonstrating high thermoelectric conversion efficiency. The high‐performance n‐type GeTe‐based material matching well with p‐type GeTe‐based materials can promote the corresponding practical applications. Compatible p‐ and n‐type materials are necessary for high‐performance GeTe thermoelectric modules, where the n‐type counterparts are in urgent need. Here, it is reported that the p‐type GeTe can be tuned into n‐type by decreasing the formation energy of Te vacancies via AgBiTe2 alloying. AgBiTe2 alloying induces Ag2Te precipitates and tunes the carrier concentration close to the optimal level, leading to a high‐power factor of 6.2 μW cm−1 K−2 at 423 K. Particularly, the observed hierarchical architectural structures, including phase boundaries, nano‐precipitates, and point defects, contribute an ultralow lattice thermal conductivity of 0.39 W m−1 K−1 at 423 K. Correspondingly, an increased ZT of 0.5 at 423 K is observed in n‐type (GeTe)0.45(AgBiTe2)0.55. Furthermore, a single‐leg module demonstrates a maximum η of 6.6% at the temperature range from 300 to 500 K. This study indicates that AgBiTe2 alloying can successfully turn GeTe into n‐type with simultaneously optimized thermoelectric performance.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Interfacial Design Contributing to High Conversion Efficiency in Mg3(Sb, Bi)2/Bi2Te3 Thermoelectric Module with Superior Stability

Nuo Qu,Yuxin Sun,Zihang Liu,Liangjun Xie,Yuke Zhu,Hao Wu,Ronghao Chai,Jinxuan Cheng,Fengkai Guo,Qian Zhang,Ruiqi Wang,Bangming Li,Zhiguo Wei,Wei Cai,Jiehe Sui

DOI: https://doi.org/10.1002/aenm.202302818

IF: 27.8

2023-12-24

Advanced Energy Materials

Abstract:Here, it is demonstrated that Fe‐foil/Mg3(Sb, Bi)2 interface sintered at 1073 K effectively prevented a significant diffusion and realized the dual purpose of realizing both the material's high performance and low interfacial resistance. Coupled with p‐type Bi2Te3, a high‐performance thermoelectric module is fabricated showing a competitive efficiency of 7.1% at the hot‐side temperature of 523 K. Mg3(Sb, Bi)2‐based materials possess excellent room‐temperature thermoelectric performance, while poor interfacial behaviors occur when connected with metal electrodes due to the strong chemical activity and volatility of Mg element. In this study, a high efficiency of 7.1% under a temperature difference of 230 K is achieved in n‐Mg3(Sb, Bi)2/p‐Bi2Te3 thermoelectric module. When changing the interfacial layer from Fe powder to Fe foil, it effectively prevents a significant diffusion of both Mg and Bi elements from the material matrix to the interfacial layer, resulting in an extremely low contact resistivity ≈3.4 μΩ cm2 that is almost one order lower than of that of Fe powder/Mg3(Sb, Bi)2 junction ≈30 μΩ cm2. Particularly, a thin diffusion layer with a width of ≈2 μm is initially observed in the unannealed Fe foil/Mg3(Sb, Bi)2 junction. Even after thermal aging at 573 K for 28 days, the diffusion‐layer width is basically unchanged and its corresponding contact resistivity maintained as low as ≈5.8 μΩ cm2. Overall, this work provides deep insights into interfacial design and paves the way for high‐performance and sustainable low‐grade waste heat recovery.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,energy & fuels
Charge transfer engineering to achieve extraordinary power generation in GeTe-based thermoelectric materials

Chengyan Liu,Zhongwei Zhang,Ying Peng,Fucong Li,Lei Miao,Eiji Nishibori,Raju Chetty,Xiaobo Bai,Ruifan Si,Jie Gao,Xiaoyang Wang,Yanqiu Zhu,Nannan Wang,Haiqiao Wei,Takao Mori

DOI: https://doi.org/10.1126/sciadv.adh0713

IF: 13.6

2023-04-28

Science Advances

Abstract:By the fine manipulation of the exceptional long-range germanium-telluride (Ge─Te) bonding through charge transfer engineering, we have achieved exceptional thermoelectric (TE) and mechanical properties in lead-free GeTe. This chemical bonding mechanism along with a semiordered zigzag nanostructure generates a notable increase of the average zT to a record value of ~1.73 in the temperature range of 323 to 773 K with ultrahigh maximum zT ~ 2.7. In addition, we significantly enhanced the Vickers microhardness numbers ( H v ) to an extraordinarily high value of 247 H v and effectively eliminated the thermal expansion fluctuation at the phase transition, which was problematic for application, by the present charge transfer engineering process and concomitant formation of microstructures. We further fabricated a single-leg TE generator and obtained a conversion efficiency of ~13.4% at the temperature difference of 463 K on a commercial instrument, which is located at the pinnacle of TE conversion.

multidisciplinary sciences
A high-efficiency GeTe-based thermoelectric module for low-grade heat recovery

Zhe Guo,Kun Song,Ruoyu Wang,Xiaojian Tan,Lidong Chen,Gang Wu,Qiang Zhang,Peng Sun,Guo-Qiang Liu,Jun Jiang

DOI: https://doi.org/10.1039/d2ta00960a

IF: 11.9

2022-01-01

Journal of Materials Chemistry A

Abstract:The thermoelectric properties of GeTe (300 ∼ 700 K) are significantly improved, leading to a conversion efficiency of 8.6% with T c = 300 K and T h = 700 K.

materials science, multidisciplinary,chemistry, physical,energy & fuels
Realizing High-Performance Thermoelectric Modules Through Enhancing the Power Factor Via Optimizing the Carrier Mobility in N-Type PbSe Crystals

Siqi Wang,Yi Wen,Shulin Bai,Zhe Zhao,Yichen Li,Xiang Gao,Qian Cao,Cheng Chang,Li-Dong Zhao

DOI: https://doi.org/10.1039/d4ee00433g

IF: 32.5

2024-01-01

Energy & Environmental Science

Abstract:The limited availability of Te poses challenges for the widespread application of Bi2Te3-based thermoelectric modules. In this work, we explored the thermoelectric module potential of Te-free PbSe by elevating its power factor through crystal growth and slight-tuning vacancy and interstitial defects. The outcomes revealed a gradual increase in the carrier concentration and a high room-temperature carrier mobility of similar to 1750 cm(2) V-1 s(-1), leading to an enhanced power factor of similar to 37.4 mu W cm(-1) K-2 in Pb1.006Se+0.0016 Al crystals. We grew PbSe crystals to minimize the impact of grain boundaries on the charge carrier transport. Subsequently, n-type PbSe crystals were produced by introducing extra Pb to occupy the intrinsic Pb vacancies, effectively minimizing vacancy scattering. Following this, a minute quantity of small-sized Al (<= 2 parts per thousand) was introduced, revealing that these surplus Al atoms served as cationic dopants, substituting for Pb, while also occupying interstitial positions. The interstitial doping increases the carrier concentration while maintaining carrier mobility due to the distinct dimensions between the interstitial atoms and mean free path of electrons. The consistently improved power factor with the suppression of thermal conductivity brings about a significantly high ZT value over the whole temperature. Specifically, the ZT values of the Pb1.006Se+0.0016Al crystal reached similar to 0.5 at 300 K, similar to 1.5 at 673 K, and the average ZT (ZT(ave)) reached similar to 1.1 at 300-773 K. Ultimately, a single-leg power generation efficiency similar to 7.1% was achieved in Pb1.006Se+0.0016Al crystal and a 7-pair module reached a maximum temperature cooling difference similar to 51.2 K at the high temperature side T-h of 363 K. These results indicate the potential for developing a cost-effective and high-performance thermoelectric module utilizing PbSe.
Valence Band Modification and Enhanced Phonon‐Phonon Interactions for High Thermoelectric Performance in GeTe

Jianglong Zhu,Ruiheng Li,Xiaobo Tan,Fan Feng,Qiang Sun,Pingan Song,Min Hong,Ran Ang

DOI: https://doi.org/10.1002/adfm.202417260

IF: 19

2024-11-11

Advanced Functional Materials

Abstract:The strong coupling between carrier and phonon transport significantly restricts the enhancement of thermoelectric performance in GeTe. Herein, Zn4Sb3 alloying enlarges the bandgap and promotes band convergence, while the addition of Pb doping modifies phonon dispersion and induces multiscale hierarchical structures. This stepwise modulation of carrier and phonon transport synergistically enhances the thermoelectric performance of GeTe. The strong coupling between carrier and phonon transport in thermoelectric (TE) materials severely limits improvements to the figure of merit (ZT). In this work, an approach is proposed to weaken electron‐phonon coupling, effectively enhancing the TE performance of GeTe. Alloying with Zn4Sb3 reduces excessive carrier concentration (nH), widens the bandgap, and promotes band convergence, synergistically improving charge carrier transport and ensuring a high power factor. Additional Pb doping further optimizes nH, boosting the power factor even more. Moreover, phonon transport is suppressed through Pb doping, as reflected in enhanced acoustic‐optical interactions due to the crossing of optical and acoustic modes, and a reduction in sound group velocity. This reinforced strong phonon scattering, combined with multi‐scale hierarchical nano/microstructures in the matrix, significantly reduces lattice thermal conductivity. As a result, a high ZT of 2.1 is achieved at 753 K in Ge0.9Pb0.1Te+0.9%Zn4Sb3. Alongside optimized mechanical performance, a high power density of 1.46 W cm−2 is realized at a temperature difference of 350 K in the fabricated 7‐pair TE module. The findings demonstrate the effectiveness of a stepwise optimization strategy for developing high‐performance TE materials.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Improving the Long-Term Stability of PbTe-Based Thermoelectric Modules: From Nanostructures to Packaged Module Architecture

Philipp Sauerschnig,Noriyuki Saitou,Masanori Koshino,Takao Ishida,Atsushi Yamamoto,Michihiro Ohta

DOI: https://doi.org/10.1021/acsami.4c07148

2024-08-02

Abstract:Nanostructured lead telluride PbTe is among the best-performing thermoelectric materials, for both p- and n-types, for intermediate temperature applications. However, the fabrication of power-generating modules based on nanostructured PbTe still faces challenges related to the stability of the materials, especially nanoprecipitates, and the bonding of electric contacts. In this study, in situ high-temperature transmission electron microscopy observation confirmed the stability of nanoprecipitates in p-type Pb0.973Na0.02Ge0.007Te up to at least ∼786 K. Then, a new architecture for a packaged module was developed for improving durability, preventing unwanted interaction between thermoelectric materials and electrodes, and for reducing thermal stress-induced crack formation. Finite element method simulations of thermal stresses and power generation characteristics were utilized to optimize the new module architecture. Legs of nanostructured p-type Pb0.973Na0.02Ge0.007Te (maximum zT ∼ 2.2 at 795 K) and nanostructured n-type Pb0.98Ga0.02Te (maximum zT ∼ 1.5 at 748 K) were stacked with flexible Fe-foil diffusion barrier layers and Ag-foil-interconnecting electrodes forming stable interfaces between electrodes and PbTe in the packaged module. For the bare module, a maximum conversion efficiency of ∼6.8% was obtained for a temperature difference of ∼480 K. Only ∼3% reduction in output power and efficiency was found after long-term operation of the bare module for ∼740 h (∼31 days) at a hot-side temperature of ∼673 K, demonstrating good long-term stability.

Mucus models to evaluate nanomedicines for diffusion.

High efficiency GeTe-based materials and modules for thermoelectric power generation

High thermoelectric performance in GeTe with compositional insensitivity

Lead-free and scalable GeTe-based thermoelectric module with an efficiency of 12%

Multiphase Coherent Nanointerface Network Enhances Thermoelectric Performance for Efficient Energy Conversion and Contactless Thermosensation Applications in GeTe

Design and Fabrication of Segmented GeTe/(Bi,Sb)2Te3 Thermoelectric Module with Enhanced Conversion Efficiency

Modifying Roles of CuSbSe2 in Realizing High Thermoelectric Performance of GeTe

Realizing an excellent conversion efficiency of 14.5% in the Mg 3 Sb 2 /GeTe-based thermoelectric module for waste heat recovery

Realizing High-Efficiency Thermoelectric Module by Suppressing Donor-Like Effect and Improving Preferred Orientation in N-Type Bi2(Te, Se)3

High‐Efficiency Thermoelectric Module Based on High‐Performance Bi0.42Sb1.58Te3 Materials

High‐Performance Industrial‐Grade p‐Type (Bi,Sb)2Te3 Thermoelectric Enabled by a Stepwise Optimization Strategy

Realizing High Energy Conversion Efficiency in a Novel Segmented‐Mg3(Sb, Bi)2/Cubic‐GeTe Thermoelectric Module for Power Generation

Interface and Surface Engineering Realized High Efficiency of 13% and Improved Thermal Stability in Mg3Sb1.5Bi0.5‐Based Thermoelectric Generation Devices

Enhancing thermoelectric performance in GeTe through Ge enrichment regulation and AgCuTe alloying

Hierarchical Architectural Structures Induce High Performance in n‐Type GeTe‐Based Thermoelectrics

Interfacial Design Contributing to High Conversion Efficiency in Mg3(Sb, Bi)2/Bi2Te3 Thermoelectric Module with Superior Stability

Charge transfer engineering to achieve extraordinary power generation in GeTe-based thermoelectric materials

A high-efficiency GeTe-based thermoelectric module for low-grade heat recovery

Realizing High-Performance Thermoelectric Modules Through Enhancing the Power Factor Via Optimizing the Carrier Mobility in N-Type PbSe Crystals

Valence Band Modification and Enhanced Phonon‐Phonon Interactions for High Thermoelectric Performance in GeTe

Improving the Long-Term Stability of PbTe-Based Thermoelectric Modules: From Nanostructures to Packaged Module Architecture