Abstract:Thermoelectric materials can convert heat directly into electricity, and vice versa. As one of the excellent candidates for recovering the waste heat from industry and transportation, they have received extensive attention. The waste heat is widely dispersed and can be found in the temperature region from 323 K to higher than 1200 K. The composite materials have attracted much attention as popular materials in the field of thermoelectricity, and integrated high-temperature and low-temperature thermoelectric materials together to form a composite system with much higher thermoelectric superiority than single materials. Therefore, investigating thermoelectric materials suitable for high temperature is beneficial for their wider application. We have investigated the electric and thermoelectric properties of the novel high-temperature thermoelectric material La 2 Te 3 . A heavy-mass band occurs in the band structure and the figure of merit reaches 0.97 at 840 K. The optimal design variables were investigated to provide a reference for thermoelectric device design and applications. Comparing different sizes of the thermoelectric unit, the optimal segmented thermoelectric unit was obtained and the mechanism of performance improvement was explained. It was found that for a segmented thermoelectric device, there is an optimal length ratio for the n- and p-type thermoelectric materials corresponding to the maximum output power or highest conversion efficiency, but the optimal length ratios for the maximum output power and efficiency are different. Through simulation analysis and calculation, we found that the structure optimization can improve the output power and efficiency of the thermoelectric unit by 35.67% and 26.51%, respectively. In this paper, a high performance thermoelectric material La 2 Te 3 was obtained through the theoretical calculation, and combined it with low- and medium-temperature thermoelectric materials to form a composite thermoelectric structure, and optimized the structure. This work provides a reference for the design and fabrication of high efficiency segmented thermoelectric devices. Graphical abstract An efficient high temperature thermoelectric material La 2 Te 3 was obtained by calculation, and the structure of the segmented thermoelectric unit composed of this material was optimized.

Numerical Modeling and Optimization of the Segmented PbTe–BiTe-based Thermoelectric Leg

Numerical Modeling of the Performance of Thermoelectric Module with Polydimethylsiloxane Encapsulation

Design and Fabrication of Segmented GeTe/(Bi,Sb)2Te3 Thermoelectric Module with Enhanced Conversion Efficiency

Realizing Excellent Thermoelectric Performance of Sb2Te3 Based Segmented Leg with a Wide Temperature Range Using One‐Step Sintering

Optimization of segmented thermoelectric devices composed of high-temperature thermoelectric material La 2 Te 3

Designing good compatibility factor in segmented Bi0.5Sb1.5Te3 – GeTe thermoelectrics for high power conversion efficiency

Geometry Optimization of a Segmented Thermoelectric Generator Based on Multi-parameter and Nonlinear Optimization Method

Optimization of segmented thermoelectric devices composed of high-temperature thermoelectric material La2Te3

Optimization of Length Ratio in Segmented Thermoelectric Generators for Engine's Waste Heat Recovery

Effects of interfacial properties on conversion efficiency of Bi 2 Te 3 -based segmented thermoelectric devices

Optimization analysis of a segmented thermoelectric generator based on genetic algorithm

Performance evolution of thermoelectric modules under constant heat flux

Realizing High Energy Conversion Efficiency in a Novel Segmented‐Mg3(Sb, Bi)2/Cubic‐GeTe Thermoelectric Module for Power Generation

Optimization of the Performance of the SnTe Uni-Leg Thermoelectric Module Via Metallized Layers

Optimal Design of a Segmented Thermoelectric Generator Based on Three-Dimensional Numerical Simulation and Multi-Objective Genetic Algorithm

Fabrication and Characterization of Thermoelectric Power Generators with Segmented Legs Synthesized by One-Step Spark Plasma Sintering

One‐Step‐Sintered GeTe‐Bi2Te3 Segmented Thermoelectric Legs with Robust Interface‐Connection Performance

Performance Enhancement Investigation of Thermoelectric Cooler with Segmented Configuration

Study of Diverse Leg Geometry Effect on the Performance of Segmented Thermoelectric Generator with the Same Leg Volume

Segmental material design in thermoelectric devices to boost heat-to-electricity performance

Estimation of thermoelectric and mechanical performances of segmented thermoelectric generators under optimal operating conditions