Abstract:Abstract Microchannels are utilised on material surfaces of a body, allowing coolant to pass through them and enabling heat dissipation by increased contact area. Fabrication of metal surface microchannels is primarily achieved by employing a micro-milling process, which has drawbacks such as excessive cutting forces, top burrs, tool wear, and lower tool life. Alternatively, it is also realised by using Laser micro milling, which has problems associated with lower quality of surface finish, un-desired taper, heat-affected zone, and spatters. The existing literature, after due review of the current state of the art, has brought out gaps needing attention. These gaps are limited capability to reduce surface roughness, unaddressed burr width, and irregular bottom surface morphology, which affect microchannel quality. These gaps motivate this research work to improve and sustain the microchannel quality. To achieve the goals, this research work performs the fabrication of microchannels by micro-milling with automated laser assistance being achieved in two ways (a) sequentially, (b) non-sequentially, termed as LASMM and LPCMM, which are novel for the scientific community. The effects of micro milling parameters, spindle speed and feed on the quality were analysed while machining commercially pure titanium (cp-Ti). Results show that laser assistance to micro-milling provides a lower generation of undesired forces and lesser top burrs compared to micro-milling alone. In sequential laser assistance, the channels have a mean down burr width ~ 58% lower and a maximum down burr width ~ 38% lower than the channels done non-sequentially. In the case of up-burr width, a mean value ~ 60% lower and a maximum value ~ 73% lower is achieved in channels done non-sequentially as compared to those done sequentially. In the case of surface roughness, channels done sequentially have a maximum Sa value of 1.508 μm, a maximum Sq value of 1.912 μm whereas non-sequentially, they show a maximum Sa value of 3.495 μm, maximum Sq value of 4.59 μm. Steady tool wear is observed sequentially, whereas in non-sequential, rapid tool wear occurs after 500 mm of cutting length.

Study on kerf width deviation of microchannel with various medium in laser transmission cutting by diode pump fiber laser

Experimental Research on CO_2 Laser Direct-writing Machining PMMA Microchannel

Dynamic Interface for Three-Dimensional Transient Laser Ablation Polymer Microchannels

An experimental investigation of micro-channels on transparent material using Nd: YAG laser transmission technique

Investigations of the Laser Ablation Mechanism of PMMA Microchannels Using Single-Pass and Multi-Pass Laser Scans

Optimizing laser-based micro-cutting for PMMA microfluidic device fabrication: thermal analysis and parameter optimization

A combined approach of artificial neural network, multi-objective genetic algorithm, and response surface methodology for enhanced PMMA micro-channeling in low power fiber laser beam machining

Study on the influence of Fs-laser power on the entrance morphology of vessel microfluidic chips

Experimental Investigation on Laser Micromilling of SiC Microchannels

Experimental study on direct fabrication of micro channel on fused silica by picosecond laser

Experimental Investigation on Processing of Fused Silica Microchannels by High Repetition Rate Femtosecond Laser

3d Finite Element Modeling Of Laser Machining Pmma

Towards automated micromachining of PMMA micro channels using CO2 laser and sacrificial mask process

Quality enhancement of micro-milled channels with automated laser assistance

Fabrication of millimeter-scale deep microchannels in fused silica by femtosecond laser filamentation effect

Microchanneling on bio-inert dental ceramic using dry pulsed laser ablation and liquid supported pulsed laser ablation approach

Experimental Investigation and Optimization of Laser Induced Plasma Micromachining Using Flowing Water

Fabrication of Microchannels on Silica Glass by Femtosecond Laser Multi-Scan： from Surface Generation Mechanism to Morphology Control

Shape Regulation of Tapered Microchannels in Silica Glass Ablated by Femtosecond Laser with Theoretical Modeling and Machine Learning.

Experimental Study of Kerf Machined by Micro-WEDM

Femtosecond Laser Engraved 2D Tunable Optofluidic Liquid Core/Air Cladding Channel Waveguides on PDMS