Abstract:Laser-induced plasma micromachining (LIPMM) can be used to fabricate high-quality microstructures of hard and brittle materials. The liquid medium of the LIPMM process plays a key role in inducing the plasma and cooling the materials, but the liquid medium is overheated which induces lots of bubbles to defocus the laser beam and reduce machining stability. In this paper, a comparative investigation on bubble behavior and its effect on the surface integrity of microchannels in three types of liquids and at different depths during LIPMM has been presented. Firstly, the formation mechanism of microbubbles was described. Secondly, a series of experiments were conducted to study the number and maximum diameter of the attached bubbles and the buoyancy movement of floating bubbles in the LIPMM of single-crystal silicon under deionized water, absolute ethyl alcohol, and 5.6 mol/L phosphoric acid solution with a liquid layer depth of 1–5 mm. It was revealed that the number and maximum diameter of attached bubbles in deionized water were the highest due to its high tension. Different from the continuous rising of bubbles at the tail of the microchannels in the other two liquids, microbubbles in 5.6 mol/L phosphoric acid solution with high viscosity rose intermittently, which formed a large area of bubble barrier to seriously affect the laser focus, resulting in a discontinuous microchannel with an unablated segment of 26.31 μm. When the depth of the liquid layer was 4 mm, absolute ethyl alcohol showed the advantages in narrow width (27.15 μm), large depth (16.5 μm), and uniform depth profile of the microchannel by LIPMM. This was because microbubbles in the anhydrous ethanol quickly and explosively spread towards the edge of the laser processing zone to reduce the bubble interference. This research contributes to a better understanding of the behavior and influence of bubbles in different liquid media and depths in LIPMM of single-crystal silicon.

Comparative Analysis of Bubbles Behavior in Different Liquids by Laser-Induced Plasma Micromachining Single-Crystal Silicon

Bubbling Behaviors Induced by Gas-Liquid Mixture Permeating Through A Porous Medium

Laser-Induced Bubble Dynamics Optimization for High-Aspect-Ratio 3D Micro-Fluidic Channels Fabrication

Study on machining characteristics of magnetically controlled laser induced plasma micro-machining single-crystal silicon

Laser-induced microjet-assisted ablation for high-quality microfabrication

Surface microfabrication using coaxial waterjet assisted laser-induced plasma micromachining

Micro-Fabrication and Monitoring of Three-Dimensional Microstructures Based on Laser-Induced Thermoplastic Formation

Experimental Research on CO_2 Laser Direct-writing Machining PMMA Microchannel

A comparative investigation on micro-channel by using direct laser ablation and liquid-assisted laser ablation on zirconia

Experimental Investigation on Submerged Gas-Liquid Mixture Injection into Water Through A Micro-Channel

Micron-size bubble defects in fused silica and its laser induced damage near 355 nm

Influence of focus positions on underwater femtosecond laser dicing of silicon wafer

Laser ablation in liquid: bridge from a plasma stage to bubble formation

Channel-controlled Janus Membrane Fabricated by Simultaneous Laser Ablation and Nanoparticles Deposition for Underwater Bubbles Manipulation

Preliminary Study of Ultrasonic Assisted Underwater Laser Micromachining of Silicon

Laser Controlled Manipulation of Microbubbles on a Surface with Silica-Coated Gold Nanoparticle Array

Liquid-Assisted Femtosecond Laser Precision-Machining of Silica.

Experimental Investigation and Optimization of Laser Induced Plasma Micromachining Using Flowing Water

Investigations of the Laser Ablation Mechanism of PMMA Microchannels Using Single-Pass and Multi-Pass Laser Scans

Direct laser writing of 3D microstructures at solid-liquid interfaces by plasmonic bubbles

Laser-induced surface structures at polymer surfaces irradiated by ns-UV-laser in water confinement and in air