Abstract:Abstract Microchannels are utilised on material surfaces of a body, allowing coolant to pass through them and enabling heat dissipation by increased contact area. Fabrication of metal surface microchannels is primarily achieved by employing a micro-milling process, which has drawbacks such as excessive cutting forces, top burrs, tool wear, and lower tool life. Alternatively, it is also realised by using Laser micro milling, which has problems associated with lower quality of surface finish, un-desired taper, heat-affected zone, and spatters. The existing literature, after due review of the current state of the art, has brought out gaps needing attention. These gaps are limited capability to reduce surface roughness, unaddressed burr width, and irregular bottom surface morphology, which affect microchannel quality. These gaps motivate this research work to improve and sustain the microchannel quality. To achieve the goals, this research work performs the fabrication of microchannels by micro-milling with automated laser assistance being achieved in two ways (a) sequentially, (b) non-sequentially, termed as LASMM and LPCMM, which are novel for the scientific community. The effects of micro milling parameters, spindle speed and feed on the quality were analysed while machining commercially pure titanium (cp-Ti). Results show that laser assistance to micro-milling provides a lower generation of undesired forces and lesser top burrs compared to micro-milling alone. In sequential laser assistance, the channels have a mean down burr width ~ 58% lower and a maximum down burr width ~ 38% lower than the channels done non-sequentially. In the case of up-burr width, a mean value ~ 60% lower and a maximum value ~ 73% lower is achieved in channels done non-sequentially as compared to those done sequentially. In the case of surface roughness, channels done sequentially have a maximum Sa value of 1.508 μm, a maximum Sq value of 1.912 μm whereas non-sequentially, they show a maximum Sa value of 3.495 μm, maximum Sq value of 4.59 μm. Steady tool wear is observed sequentially, whereas in non-sequential, rapid tool wear occurs after 500 mm of cutting length.

A combined approach of artificial neural network, multi-objective genetic algorithm, and response surface methodology for enhanced PMMA micro-channeling in low power fiber laser beam machining

Prediction and optimization of Nd: YAG laser transmission micro-channelling on PMMA employing an artificial neural network model

Prediction of quality characteristics of micro-channels by deep learning algorithm during laser transmission ablation of PMMA

Experimental Research on CO_2 Laser Direct-writing Machining PMMA Microchannel

Investigations of the Laser Ablation Mechanism of PMMA Microchannels Using Single-Pass and Multi-Pass Laser Scans

Optimizing laser-based micro-cutting for PMMA microfluidic device fabrication: thermal analysis and parameter optimization

Optimization of Laser Cutting Parameters for PMMA Using Metaheuristic Algorithms

An experimental investigation of micro-channels on transparent material using Nd: YAG laser transmission technique

3d Finite Element Modeling Of Laser Machining Pmma

Investigation on Polymer Hybrid Composite Through CO2 Laser Machining for Precise Machining Conditions

Simultaneous optimization of process parameters during abrasive water jet machining on glass fibre reinforced polymer

Fabrication of micro holes using low power fiber laser: surface morphology, modeling and soft-computing based optimization

Quality enhancement of micro-milled channels with automated laser assistance

Selective LASER Melting Part Quality Prediction and Energy Consumption Optimization

Experimental investigation of sawing approach of low power fiber laser cutting of titanium alloy using particle swarm optimization technique

Prediction and optimization kerf width in laser beam machining of titanium alloy using genetic algorithm tuned adaptive neuro-fuzzy inference system

Towards automated micromachining of PMMA micro channels using CO2 laser and sacrificial mask process

Machine learning-driven process of alumina ceramics laser machining

Neural Network Modeling and Particle Swarm Optimization (PSO) of Process Parameters in Pulsed Laser Micromachining of Hardened AISI H13 Steel

Machine learning guided adaptive laser power control in selective laser melting for pore reduction

Optimization of CNC CO2 Laser Cutting Process Parameters on Acrylic Cutting Using Taguchi Grey Relational Analysis and Response Surface Methodology