Abstract:The performance of interacting metal surfaces having sliding motion is enhanced by fabricating microfeatures on-top of the surfaces. Laser powder bed fusion (LPBF) is used to fabricate the microfeatures of IN625 on-top of a flat surface. In LPBF, geometrical characteristics of microfeatures are based on the energy supplied and the volume of material melted (layer thickness) at that instant of time. There is very few research reported in open literature on the effect of layer thickness on microfeatures geometry during LPBF. In this work, a series of single tracks is fabricated with different combinations of laser power and scanning speed for 75 μm , 100 μm , and 125 μm layer thickness and its effect on single track geometrical characteristics and microstructure was evaluated. It has been found that laser power and scanning speed have a significant influence on the track geometry irrespective of layer thickness. The minimum linear energy density of 2.5 J/mm is considered to fabricate the continuous track formation for investigated layer thickness. From statistical analysis, it is observed that the laser power and scanning speed shows higher contribution on track width and remelting depth, respectively. Whereas, layer thickness shows a higher influence on track height and contact angle of single track as compared to laser power and scanning speed. In 125 μm layer thickness, the volume of material melting is increased which encourages the gravity effect to deform the melt pool and produces larger track width compare to 100 μm layer thickness. Further, the cell spacing is gradually increased with layer thickness resulting increase in the solidification period. The shape controllability of the single track is significantly increased with layer thickness, but as keeps on increasing layer thickness due to the larger volume of molten metal , the melt pool losses ability to maintain convex shapes. An Artificial Neural Network (ANN) model is developed to understand the relationship between the LPBF process parameters and single track geometrical characteristics to predict the responses for a wide range of process parameters. The multiple response neural network model shows excellent agreement with experimental results with R2 value greater than 0.95.

Prediction of quality characteristics of micro-channels by deep learning algorithm during laser transmission ablation of PMMA

Prediction and optimization of Nd: YAG laser transmission micro-channelling on PMMA employing an artificial neural network model

Dynamic Interface for Three-Dimensional Transient Laser Ablation Polymer Microchannels

Transient Ablation Model for Laser Machining Polymer Microfluidic Chip

A combined approach of artificial neural network, multi-objective genetic algorithm, and response surface methodology for enhanced PMMA micro-channeling in low power fiber laser beam machining

An experimental investigation of micro-channels on transparent material using Nd: YAG laser transmission technique

3d Finite Element Modeling Of Laser Machining Pmma

Investigations of the Laser Ablation Mechanism of PMMA Microchannels Using Single-Pass and Multi-Pass Laser Scans

Neural network-based prediction for surface characteristics in CO2 laser micro-milling of glass fiber reinforced plastic composite

Experimental Research on CO_2 Laser Direct-writing Machining PMMA Microchannel

Neural networks for predicting kerf characteristics of CO2 laser-machined FFF PLA/WF plates

Study on kerf width deviation of microchannel with various medium in laser transmission cutting by diode pump fiber laser

Traditional machine learning and deep learning for predicting melt-pool cross-sectional morphology of laser powder bed fusion additive manufacturing with thermographic monitoring

Optimizing laser-based micro-cutting for PMMA microfluidic device fabrication: thermal analysis and parameter optimization

Shape Regulation of Tapered Microchannels in Silica Glass Ablated by Femtosecond Laser with Theoretical Modeling and Machine Learning.

Experimental study and neural network model based prediction of layer thickness influence on LPBF IN625 single track geometry

Prediction of molten pool temperature and processing quality in laser metal deposition based on back propagation neural network algorithm

A Model to Predict the Ablation Width and Calculate the Ablation Threshold of Femtosecond Laser

Process modeling and optimization in laser drilling of bulk metallic glasses based on GABPNN and machine vision

Deep neural network for microstructured polymer fiber modeling

Predictions of Additive Manufacturing Process Parameters and Molten Pool Dimensions with a Physics-Informed Deep Learning Model