Abstract:Modern microelectronic components for high-power and high-frequency applications based on III-V compound semiconductors offer high break down voltage (GaN: 5 MV/cm and AlN: 15 MV/cm) at low specific on-resistance. However, it requires reliability and reproducibility of the production processes. Going to higher frequencies (5 GHz and beyond) and more integration in consumer electronics, smaller structure sizes are needed. This is going along with increasing demands on the manufacturing processes like dry etching. The main goal is to reach smaller and high controllable etching rates, going down to single atomic layers, low damage, and minimized surface roughness. Atomic layer etching (ALE) represents a key technology in order to achieve such requirements. An ALE process consists of two independent steps forming a repeatable cycle with a specific etching amount per cycle (EPC). First a surface modification is done by a chemical precursor i.e., adsorbing or oxidizing the surface. The second step is the removal of the modified layer, either physically by low energy non-reactive ion bombardment (Plasma Enhanced ALE [PEALE]) or chemically by a reactive species (Thermal ALE). The two steps are separated by an inert gas purge. This purging grants the removal of the chemistry after the first step, preventing further chemical reaction and transporting the chemical products out of the chamber after the second step. In this study, a PEALE conducted on different tools is used, for gate and contact recess study in a AlGaN/GaN heterostructure to form high electron mobility transistors (HEMT) with reduced ohmic contact resistance and threshold voltages. The results show a reduction of ohmic contact resistance at reduced forming temperatures and a linear dependence of the threshold voltage on gate recess depth. In order to determine the etching rate and roughness, atomic force microscopy (AFM) measurements were performed. The PEALE module is either integrated into a cluster tool consisting of atomic layer deposition (ALD) and chemical vapor deposition (CVD) or done in a combined ALD/ALE chamber. This opens the possibility of etching and depositing in-situ , reducing contamination and degradation of the substrate material. By this means, metal insulator semiconductor (MIS)-HEMTS with a recessed gate are studied. The monitoring of the individual processes is achieved by test structures like transfer length method structures (TLM) and metal oxide semiconductor (MOS), which showed the improved electric performance of these devices and may indicate unwanted interface issues, respectively. Additional, pre- and post-treatments could improve the interfaces further. The results will be presented and discussed in terms of ALE process development and optimization. This work was financially supported within the ALEStar project by the government of the Free-state of Saxony and the European Regional Development Fund under grant no. SAB 100402929.

Smooth wet etching by ultraviolet-assisted photoetching and its application to the fabrication of AlGaN/GaN heterostructure field-effect transistors

A Novel Oxidation-Based Wet Etching Method For Algan/Gan Heterostructures

Demystifying metal-assisted chemical etching of GaN and related heterojunctions

Morphological and Electrical Characterization of AlGaN/GaN Heterostructures Modified By Atomic Layer Etching

KOH Wet Etching Ga-polar AlGaN Epilayer for Ultraviolet B Photodetection with Low Dark Current and High Sensitivity

Application of Wet Chemical Etching in GaN-based Materials

The Effect of Wet Chemical Etching by KOH Solution to the Contact on the Solar-Blind Al 0.65 Ga 0.35 N Material

Dry Etching Characteristics of Algan/Gan Heterostructures Using Inductively Coupled H-2/Cl-2, Ar/Cl-2 and Bcl3/Cl-2 Plasmas

Electrochemical etching of highly conductive GaN single crystals

Preparation and Characterization of GaN Micro/nano-Structures by the Electrodeless Photo-Assisted Chemical Etching

Fabrication of recessed-gate AlGaN/GaN MOSFETs using TMAH wet etching with Cu ion implantation

Fabrication technology for high light-extraction ultraviolet thin-film flip-chip (UV TFFC) LEDs grown on SiC

Metal-Assisted Chemical Etching for Anisotropic Deep Trenching of GaN Array

Fabrication of normally-off AlGaN/GaN metal–insulator–semiconductor high-electron-mobility transistors by photo-electrochemical gate recess etching in ionic liquid

Wet etching of GaN, AlN, and SiC: a review

Investigation of Oxidation Process in Self-Terminating Gate Recess Wet Etching Technique for Algan/Gan Normally-Off Mosfets

Improved Ultraviolet Detection and Device Performance of Al 2 O 3 -Dielectric in 0.17 Al 0.83 N/AlN/GaN MOS-HFETs

A Novel Atomic-Level Post-Etch-Surface-Reinforcement Process for High-Performance p-GaN Gate HEMTs Fabrication

Nonselective and smooth etching of GaN/AlGaN heterostructures by inductively coupled plasmas

Photoelectrochemical Etching Technology for Gallium Nitride Power and RF Devices

Oxidation-based wet-etching method for AlGaN/GaN structure with different oxidation times and temperatures