Abstract:In order to achieve desired mechanical properties of alloys by manipulating grain boundaries (GBs) via solute decoration, it is of great significance to understand the underlying mechanisms of microstructural evolution and plastic deformation. In this work, nanocrystalline (NC) Cu-W alloyed films with W concentrations spanning from 0 to 40 at% were prepared by using magnetron sputtering. Thermal stability (within the temperature range of 200 °C-600 °C) and hardness of the films were investigated by using the x-ray diffraction, transmission electron microscope (TEM) and nanoindentation, respectively. The NC pure Cu film exhibited substantial grain growth upon all annealing temperatures. The Cu-W alloyed films, however, displayed distinct microstructural evolution that depended not only on the W concentration but also on the annealing temperature. At a low temperature of 200 °C, all the Cu-W alloyed films were highly stable, with unconspicuous change in grain sizes. At high temperatures of 400 °C and 600 °C, the microstructural evolution was greatly controlled by the W concentrations. The Cu-W films with low W concentration manifested abnormal grain growth (AGG), while the ones with high W concentrations showed phase separation. TEM observations unveiled that the AGG in the Cu-W alloyed thin films was rationalized by GB migration. Nanoindentation results showed that, although the hardness of both the as-deposited and annealed Cu-W alloyed thin films monotonically increased with W concentrations, a transition from annealing hardening to annealing softening was interestingly observed at the critical W addition of ∼25 at%. It was further revealed that an enhanced GB segregation associated with detwinning was responsible for the annealing hardening, while a reduced solid solution hardening for the annealing softening.

Insight into the Microstructure and Tensile Behavior of the W–Cu Composite Reinforced with Tungsten Fibers and Particulates

Long-term Ball Milling and Hot Pressing of In-Situ Nanoscale Tungsten Carbides Reinforced Copper Composite and Its Characterization

Experimental Investigation of Tensile Properties and Fracture Mechanism of WCP/Cu Composites Reinforced with Different WCP Volume Fraction

Microstructure and high-temperature mechanical properties of Cu-W composite prepared by hot isostatic pressing

Microstructure and properties of W Cu composites reinforced by in-situ generated WC

Enhanced Tensile Ductility of Tungsten Microwires Via High-Density Dislocations and Reduced Grain Boundaries

Multilayered W-Cu composites with enhanced strength, electrical conductivity and wear resistance

Freeze-casted tungsten skeleton reinforced copper matrix composites

The W alloying effect on thermal stability and hardening of nanostructured Cu-W alloyed thin films

The Effect of Y2O3 Particles on the Microstructure and Mechanical Properties of Tungsten Fiber-Reinforced Tungsten Composites

High-temperature mechanical and electrical properties of W-particle-reinforced Cu-matrix composites from improved electroless plated powders

Microstructure and mechanical properties of tungsten fiber reinforced tungsten composites prepared by Fe activated sintering

Fracture Behavior of Cu/Cu–WCP Layered Composites

Interfacial Failure Mechanism in Tungsten Fiber Reinforced Copper-Based Composites Fabricated by Combustion Synthesis Melt Infiltration under Ultra-High Gravity

Mechanical and tribological properties of WC particles reinforced Cu-20Zn matrix composites

Microstructure and mechanical properties of WC reinforced 18Ni300 composites produced by selective laser melting

Interfacial Microstructure and Mechanical Property of the Discontinuous Short Tungsten Fiber-Reinforced Tungsten Matrix Composites

Enhanced mechanical properties and thermal conductivity of W-30Cu composite fabricated with monodisperse and nearly spherical W powder

The effects of ultrasonic vibration on mechanical properties of tungsten particle-reinforced copper-matrix composites

Effect of Grain Refinement on the Comprehensive Mechanical Performance of W–Cu Composites

Microstructural evolution and performance analysis of WC-11Co reinforced iron matrix composites