Abstract:In this study, the effect of the mechanical stability of residual austenite in a carburizing layer on the wear performance was explored. First, different amounts of residual austenite were obtained by quenching and cooling 23CrNi3MoA steel after carburization. The effects of the volume fraction, size, and distribution of the residual austenite on the stability and wear performance were investigated. Second, scanning electron microscopy (SEM), transmission electron microscopy (TEM), focused ion beam (FIB), and electron backscatter diffraction (EBSD) analyses were used to characterize the severely deformed layer under friction. In addition, the impacts of the size, morphology, content, and distribution of residual austenite on the wear performance were analyzed. The final results indicated that as the k of the residual austenite decreased, the wear performance of the sample first increased and then decreased. The wear performance improved due to the reduced stability of the residual austenite, which facilitated phase transformation of the residual austenite under friction. The phase transformation of residual austenite into martensite increased the hardness of the wear surface layer. In addition, nanotwinned martensite formed in the severe wear deformation layer. The generation of nanotwins could effectively hinder dislocation movement and store high-density dislocations near the twin boundaries, thereby improving the strength of the wear layer and reducing the wear rate. However, when the residual austenite stability continued to decrease, a large amount of block-like austenite at the grain boundaries underwent excessive plastic deformation during friction. This excessive plastic deformation increased the number of dislocations and led to incoordination between the phase-transformed martensite and the original martensite during deformation. Therefore, crack nucleation increased, and crack propagation accelerated, directly increasing the amount of wear on the wear surface and decreasing the overall wear resistance of the material. In this article, the wear mechanism of residual austenite during dry sliding friction was elucidated, and a basis for reasonable control of residual austenite in production work was provided.

Effect of Grain Size on the Friction-Induced Martensitic Transformation and Tribological Properties of 304 Austenite Stainless Steel

Effect of prior austenite grain size on the abrasive wear resistance of ultra-high strength martensitic steels

Friction and Wear Mechanisms of 316L Stainless Steel in Dry Sliding Contact: Effect of Abrasive Particle Size

Wear Rate, Frictional Temperature, and Energy Consumption of Steel 52100 with Different Microstructures During Sliding

Effect of loading on microstructure and friction and wear behavior of an austenite lightweight steel

Analyzing the effect of the mechanical stability of residual austenite on the wear performance

Effects of Grain Size on Mechanical Properties and Work‐Hardening Behavior of AISI 304 Austenitic Stainless Steel

Cryogenic tribological behavior of coarse, ultrafine grained and heterogeneous Fe-18Cr-8Ni austenitic stainless steel

Effect of Variation of Martensite with a Constant Carbon Content on Mechanical Behavior and Sliding Wear of Dual Phase Steels

The Study of Micro-grating and Micro-square-column on Frictional Resistance Reduction of 316L Stainless Steel Surface

Effect of Grain Size on the Plastic Deformation Behaviors of a Fe-18Mn-1.3Al-0.6C Austenitic Steel

The role of austenite grain size on martensite start temperature and phase transformation path in SUS321 stainless steel

Effects of Chemical Composition and Morphological Structure of Surface Oxides on the Antifrictional Properties of Medium Carbon Steel

Unraveling the significant role of retained austenite on the dry sliding wear behavior of medium manganese steel

Strain‐Induced Martensitic Transformation and the Mechanism of Wear and Rolling Contact Fatigue of AISI 301LN Metastable Austenitic Stainless Steel

Plastic Deformation Effect on Wear and Corrosion resistance of Super Martensitic Stainless Steel

The influence of austenitizing temperature on prior austenite grain size and resistance to abrasion wear of selected low-alloy boron steel

Effect of Nanosecond Laser Texturization on Tribological Behavior of AISI 321 Stainless Steel

Optimizing tribological property by inducing the gradient microstructure and surface topography in martensite stainless steel

Grain coarsening of nano laminated structure in martensite steel under sliding wear

Effect of grain size on fatigue strength of 304 stainless steel