Abstract:This study investigated the effect of grain size distribution on the deformation behavior in fine-grained (FG) austenitic stainless steels (γ-SSs). Commercial Cr–Mn–N γ-SS was selected as the coarse-grained (CG) specimen, which was cold rolled and then annealed at 1000 °C for 60 s and 700 °C for 3600 s to obtain FG specimens with similar grain sizes but different grain size distributions. The CG specimens annealed at 1000 °C for 60 s and 700 °C for 3600 s were referred to as unimodal-FG and bimodal-FG specimens, respectively. The tensile properties revealed that the yield strength was enhanced from 383 MPa to 685 MPa when the grain size was refined from CG (10.7 μm) to FG (∼1.8 μm). Moreover, the bimodal-FG specimen exhibited a higher total elongation of 48% than 36.5% for the unimodal-FG specimen. Transmission electron microscopy, electron backscatter diffraction and X-ray diffraction were used to identify the microstructural characteristics during tension. The results indicated that the main deformation mechanisms of γ-SSs specimens during tension were dislocation generation and accumulation at the initial stage, deformation twinning at the intermediate stage, and deformation-induced martensite (DIM) at the final stage. Compared with the unimodal-CG counterpart, grain refinement in the unimodal-FG specimens restricted the formation of DIM due to the increased austenite stability. A newly discovered phenomenon was that the bimodal-FG specimens promoted the formation of geometrically necessary dislocation (GND) and DIM compared to the unimodal-FG, which was due to the uneven deformation in grains located on hetero-boundaries (HBs). Moreover, the bimodal-FG specimen was preferentially formed DIM on HBs, especially in the smaller grains side rather than inside larger grains due to the higher stress concentration in smaller grains.

Effects of Grain Size on Mechanical Properties and Work‐Hardening Behavior of AISI 304 Austenitic Stainless Steel

Effects of grain refinement on the quasi-static compressive behavior of AISI 321 austenitic stainless steel: EBSD, TEM, and XRD studies

Effect of Grain Size and Dislocation Density on the Work Hardening Behavior of SS 304

Effect of grain size on fatigue strength of 304 stainless steel

Grain Size-Dependent Mechanical Properties of a High-Manganese Austenitic Steel

The influence of nitrogen and grain size on yield strength in Type AISI 316L austenitic stainless steel

Effect of differences in grain size on the mechanical properties of steel 18Kh2N4MA

Linking Grain Size to Microscopic Hardening Laws in a Phenomenological Crystal Plasticity Model: A Finite Element Simulation Approach for 316L Stainless Steel

Effects of Initial Austenite Grain Size on Microstructure Evolution of Medium Carbon Steel

Enhanced Mechanical Behaviors of Gradient Nano-Grained Austenite Stainless Steel by Means of Ultrasonic Impact Treatment

Probing the impact of grain size distribution on the deformation behavior in fine-grained austenitic stainless steel: A critical analysis of unimodal structure versus bimodal structure

Achieving Excellent Strength–Ductility Synergy by Tailoring the Grain Size Distribution in a Metastable Austenitic Stainless Steel

Effect of initial microstructures on grain refinement in a stainless steel by large strain deformation

Microstructure and Mechanical Properties of Friction Stir Processed AISI 316 Stainless Steel: Evaluation of the Effect of Cooling Media and Multi-Step Processing on Microstructure and Mechanical Properties of Friction Stir Processed AISI 316 Stainless Steel

In-situ tensile deformation of austenitic stainless steels with various grain sizes during synchrotron and neutron diffraction

Grain refinement strengthening mechanism of an austenitic stainless steel: critically analyze the impacts of grain interior and grain boundary

Grain Size Dependence of Twinning Behaviors and Resultant Cryogenic Impact Toughness in High Manganese Austenitic Steel

Effect of prior austenite grain size on the abrasive wear resistance of ultra-high strength martensitic steels

Effects of grain size of AISI 304 on the machining performances in micro electrical discharge machining

Low temperature mechanical behavior of fine- and ultrafine-grained 304 austenitic stainless steel fabricated by cryogenic-rolling and annealing

Effect of Prior Austenite Grain Size on Austenite Reversion, Bainite Transformation and Mechanical Properties of Fe-2Mn-0.2C Steel