Abstract:<p>For wear resistant steels, there is generally a linear relationship between the initial hardness and wear resistance, yet a high initial hardness limits the formability of components. The intrinsic ductility of austenite and strain hardening produced from the transformation-induced plasticity (TRIP) effect during service opens a new window for this contradiction. Herein, the wear resistance and the corresponding failure mechanisms of 5Mn steels after different heat treatment processes were evaluated using a ball-on-disk sliding test under dry conditions. The wear behaviors of the counterbodies were also studied to elucidate the wear mechanism of the tribo-system. The results show that the microstructures of the hot-rolled and air-cooled steel mainly comprised martensite. When the intercritical annealing temperature was relatively low (<695°C), the microstructure primarily consisted of reversed austenite and ferrite. The samples annealed at 630°C, 645°C, 660°C, and 675°C had a similar initial hardness, while the sample annealed at 675°C possessed a wear resistance that was 3.25 times that of the steel annealed at 630°C. The large difference in the wear resistance was predominately due to the gradient of strain hardening provided by the varied amount and mechanical stability of the retained austenite. The transformation from austenite to martensite, which has an increased hardness, improves the work hardening. A strengthening layer formed with a certain thickness that provided stress support during the wear process and enhanced the wear resistance. When the annealing temperature reached 695°C, a large amount of secondary martensite was generated from austenite that had a low thermal stability, which improved the initial hardness and wear resistance. The steels with a large amount of martensite had an enhanced wear resistance, but the elongation severely deteriorated, leading to unsatisfactory formability. The present work provides guidance for designing novel steels with an excellent balance of good formability and decent wear resistance by precisely adjusting the characteristics of the retained austenite.</p>

Strain‐Induced Martensitic Transformation and the Mechanism of Wear and Rolling Contact Fatigue of AISI 301LN Metastable Austenitic Stainless Steel

Modeling the Tensile Strain Hardening Behavior of a Metastable AISI 301LN Austenitic Stainless Steel Pre-strained in Compression

Modeling of the Kinetics of Strain‐Induced Martensite Transformation and the Transformation‐Induced Plasticity Effect in a Lean‐Alloyed Metastable Austenitic Stainless Steel

Strain-induced martensite formation in cryorolled AISI 317 L stainless steel

Unraveling the significant role of retained austenite on the dry sliding wear behavior of medium manganese steel

Study on Microstructure and Fatigue Properties of A473M Stainless Steel Strengthened by Surface Rolling

Microstructural Evolution and Mechanical Properties of 6cr13 Martensitic Stainless Steel Subjected to Cold Rolling and Heat Treatments

Mechanical Behavior and Fatigue Performance of Austenitic Stainless Steel under Consideration of Martensitic Phase Transformation

Deformation induced martensite in an AISI 301LN stainless steel: characterization and influence on pitting corrosion resistance

Investigations of Metallurgical Differences in AISI 347 and Their Influence on Deformation and Transformation Behaviour and Resulting Fatigue Life

Structural Transformations and Tribological Effects in the Surface Layer of Austenitic Chrome-Nickel Steel Initiated by Nanostructuring and Oxidation

Effect of Cryorolling–Annealing and Bake-Hardening on the Microstructure and Mechanical Properties of AISI 301LN Grade Austenitic Stainless Steel

Modeling the kinetics of deformation-induced martensitic transformation in AISI 316 metastable austenitic stainless steel

Cryorolling impacts on microstructure and mechanical properties of AISI 316 LN austenitic stainless steel

TENSILE AND LCF PROPERTIES OF AISI 316LN SS AT 300 AND 77 K

Consequences of Deep Rolling at Elevated Temperature on Near-Surface and Fatigue Properties of High-Manganese TWIP Steel X40MnCrAl19-2

The effect of retained austenite on rolling/sliding contact fatigue of high carbon steel

Bending fatigue behavior of metastable and stable austenitic stainless steels with different surface morphologies

Martensitic Transformation and Work Hardening of Metastable Austenite Induced by Abrasion in Austenitic Fe-C-Cr-Mn-B Alloy - A Tem Study

Influence of the martensitic transformation on the deformation behaviour of an AISI 316 stainless steel at low temperatures

Development of materials model based on microstructure evolution for formability analysis of low-Ni austenitic stainless steel