Abstract:Herein, the cryogenically martensitic transformation and its effects on the tempering behaviors of bearing steel was investigated. An in-situ magnetic method was used for obtaining the thermodynamics of the martensitic transformation at sub-zero Celsius temperature from in respects of athermal and isothermal conditions. Microstructure evolution was also characterized systematically to investigate the mechanisms of the martensitic transformation. The results showed that the athermally martensitic transformation of samples experienced three different stages, where the martensite formed slowly at 300–230 K, rapidly at 230–120 K, and slowly again at 120–77 K during the continuous cooling process. With the increase of cooling rate, both the start and finish temperatures of the transformation rise, while the maximum transformed rate decreases. The content of retained austenite transformed isothermally is much smaller as compared to the athermal condition. The amount of isothermally formed martensite does not show linear relationship with the temperature, where an optimal isothermal temperature for GCr15 steel is 193 K in this work. XRD measurement result showed that the content of retained austenite decreased with the decrease of treating temperature in practical DCT, where the content was reduced up to 4.2% after DCT at the lowest temperature combined with tempering. DCT enhanced the precipitation of θ-carbides during tempering and altered the precipitation behavior by advancing the precipitated temperature of θ-carbides from 340 °C to 315 °C. The tempered hardness of samples was improved by DCT, which can be attributed to the enhanced carbides precipitation during tempering and lower content of retained austenite after DCT. The improvement was also affected by tempering and austenitizing temperatures. It was concluded that the performance improvement induced by DCT was most evident if DCT was conducted between higher temperature quenching and lower temperature tempering. DCT also affected the decomposition of retained austenite during tempering by decreasing the activation energy of decomposition by up to 38.13 KJ/mol, which indicated a lower thermal stability of retained austenite after DCT. Microstructure observation indicated that the substructure of the new formed martensite was dominated by ultra-fine twins, which derived from the accommodated strain induced by martensitic transformation during DCT. The transformation strain induced by DCT also causes more dislocations in the microstructure, which provides more nucleation sites for the precipitation of θ-carbides during tempering.

Martensitic Transformation and Work Hardening of Metastable Austenite Induced by Abrasion in Austenitic Fe-C-Cr-Mn-B Alloy - A Tem Study

A Study On The Dynamic Characteristics Of Abrasion For High-Chromium Alloys

In Situ Observation of the Grain Growth Behavior and Martensitic Transformation of Supercooled Austenite in NM500 Wear-Resistant Steel at Different Quenching Temperatures

The Transformation of Carbides during Austenization and Its Effect on the Wear Resistance of High Speed Steel Rolls

Carbides Dissolution in 5Cr15MoV Martensitic Stainless Steel and New Insights into Its Effect on Microstructure and Hardness

Dislocation Activities at the Martensite Phase Transformation Interface in Metastable Austenitic Stainless Steel: An In-situ TEM Study

Effect of Short-Term Low-Temperature Austempering on the Microstructure and Abrasive Wear of Medium-Carbon Low-Alloy Steel

Early Martensitic Transformation in a 0.74C–1.15Mn–1.08Cr High Carbon Steel

Work hardening behavior of hot-rolled metastable Fe50Co25Ni10Al5Ti5Mo5 medium-entropy alloy: in situ neutron diffraction analysis

Austenite transformation and work hardening of medium manganese steel

Effect of Martensitic Reversal and Grain Size on the Corrosion and Wear Behaviour of Cr-Mn Steel

Sliding wear of medium-carbon bainitic/martensitic/austenitic steel treated by short-term low-temperature austempering

Mechanical Behavior and Fatigue Performance of Austenitic Stainless Steel under Consideration of Martensitic Phase Transformation

Cryogenically martensitic transformation and its effects on tempering behaviors of bearing steel

A micro-mechanical model of non-thermo-elastic martensitic transformation

Effects of acicular ferrites on crystallography and incomplete transformation of low-carbon low-alloy steel

Effect of Spheroidizing Annealing Process on Microstructure and Properties of Quenching and Tempering 60Cr16MoMA Martensitic Stainless Steel

Stress-induced martensitic transformation in a β-solution treated Ti–10V–2Fe–3Al alloy during compressive deformation

Mechanical Properties of the (Ti0.615zr0.385)100-3.9X(cu2.3fe1.6)x Alloys Containing Amorphous Martensite

Synergistic effect of well/over-tempered hierarchical martensitic structure and carbides (M 23 C 6 and MX) on austenite growth in 9Cr steel

The Influence of Tempering Parameters on the Microstructure, Mechanical Property, and the Corresponding Strengthening Mechanism of Metastable 301 Austenitic Stainless Steel