Abstract:Through the cold rolling and annealing process, the prior metastable 301 austenitic stainless steel grains are refined to prepare nanograin and quasiheterostructure, respectively. Compared with the latter, the nanograin austenitic steel exhibits superior strength and ductility, and its excellent mechanical properties are mainly derived from grain refinement strengthening, phase‐transformation strengthening, and precipitation strengthening of Cu particles. Metastable austenitic stainless steels (MASS) are widely used in various industrial applications due to their exceptional mechanical properties. The microstructure of MASS can be regulated through severe plastic deformation, heat treatments, and surface treatments to achieve further improvement of mechanical properties. Herein, nanograin and quasiheterostructure are prepared by cold rolling and annealing process in Fe–17Cr–6Ni MASS. The mechanical response, deformation mechanism, and strengthening contribution of the two steels with representative microstructure are studied. The results indicate that nanograin austenitic steel (803 MPa, 22%) has superior yield strength and similar ductility compared with that of quasiheterostructure steel (600 MPa, 25%). In the nanograin steel, the deformation mechanism is mainly dislocation slip and deformation‐induced martensite transformation, while in quasiheterostructure steel, the deformation twinning is also included for the relative lower stacking fault energy in the coarse grain. The yield strength of nanograin structural steel is about 200 MPa higher than that of quasiheterostructure steel, which can be attributed to the differences in grain refinement strengthening, phase‐transformation strengthening, and precipitation strengthening of Cu particles. The findings presented in this study are informative for modulating MASS properties and ultimately improving the lifespan in a variety of industrial settings.

The Influence of Tempering Parameters on the Microstructure, Mechanical Property, and the Corresponding Strengthening Mechanism of Metastable 301 Austenitic Stainless Steel

Achieving High Strength and High Ductility in Nanostructured Metals: Experiment and Modelling

Microstructures-based Constitutive Analysis for Mechanical Properties of Gradient-Nanostructured 304 Stainless Steels

Achieving Excellent Strength–Ductility Synergy by Tailoring the Grain Size Distribution in a Metastable Austenitic Stainless Steel

Yielding Behavior and Strengthening Mechanisms of a High Strength Ultrafine‐Grained Cr–Mn–Ni–N Stainless Steel

Microstructural Evolution, Nanoprecipitation Behavior and Mechanical Properties of Selective Laser Melted High-Performance Grade 300 Maraging Steel

The Impact of Annealing Temperature on the Microstructure - Properties Relationship of Reversion-Induced Austenitic Stainless Steels

Micro/nano-structure leads to super strength and excellent plasticity in nanostructured 304 stainless steel

Effect of Structure Transformation in a Ultra-high Strength Maraging Stainless Steel on Its Mechanical Properties

Tailoring the tempered microstructure of a novel martensitic heat resistant steel G115 through prior cold deformation and its effect on mechanical properties

Influence of Austenitizing Temperature on the Microstructure and Mechanical Properties of an Fe-Cr-Ni-Mo-Ti Maraging Stainless Steel

Effect of annealing and strain rate on the microstructure and mechanical properties of austenitic stainless steel 316L manufactured by selective laser melting

Two-stage Rolling and Partial Annealing Enables Heterogeneous Structure and Strength-Ductility Enhancement for Austenitic Stainless Steel

Microstructure-based Finite Element Modeling of Effect of Metastable Austenite on Mechanical Properties of Quenching and Partitioning (Q&P) 980 Steel

The Role of Al/Ti in Precipitate-Strengthened and Austenite-Toughened Co-Free Maraging Stainless Steel

Effects of Forging and Heat Treatment on Martensite Lath, Recrystallization and Mechanical Properties Evolution of 18Ni(250) Maraging Steel

Achieving High Strength and High Ductility in 304 Stainless Steel Through Bi-Modal Microstructure Prepared by Post-Ecap Annealing

The combining effects of ausforming and below-Ms or above-Ms austempering on the transformation kinetics, microstructure and mechanical properties of low-carbon bainitic steel

Microstructure evolution and mechanical properties of bimodal grain sized 301 stainless steel strip induced by reverse phase transformation

Evolution of Microstructures and Mechanical Properties with Tempering Temperature in a Novel Synergistic Precipitation Strengthening Ultra-High Strength Steel

Effect of Prior Austenite Grain Size on Austenite Reversion, Bainite Transformation and Mechanical Properties of Fe-2Mn-0.2C Steel