Abstract:Miniaturization of gas chromatography (GC) instrumentation is of interest because it addresses current and future issues relating to compactness, portability and field application. While incremental advancements continue to be reported in GC with columns fabricated in microchips (referred to in this paper as "microchip columns"), the current performance is far from acceptable. This lower performance compared to conventional GC is due to factors such as pooling of the stationary phase in corners of non-cylindrical channels, adsorption of sensitive compounds on incompletely deactivated surfaces, shorter column lengths and less than optimum interfacing to injector and detector. In this work, a GC system utilizing microchip columns was developed that solves the latter challenge, i.e., microchip interfacing to injector and detector. A microchip compression clamp was constructed to heat the microchip (i.e., primary heater), and seal the injector and detector fused silica interface tubing to the inlet and outlet ports of the microchip channels with minimum extra-column dead volume. This clamp allowed occasional operation up to 375°C and routine operation up to 300°C. The compression clamp was constructed of a low expansion alloy, Kovar™, to minimize leaking due to thermal expansion mismatch at the interface during repeated thermal cycling, and it was tested over several months for more than one hundred injections without forming leaks. A 5.9m long microcolumn with rectangular cross section of 158μm×80μm, which approximately matches a 100μm i.d. cylindrical fused silica column, was fabricated in a silicon wafer using deep reactive ion etching (DRIE) and high temperature fusion bonding; finally, the channel was coated statically with a 1% vinyl, 5% phenyl, 94% methylpolysiloxane stationary phase. High temperature separations of C10-C40 n-alkanes and a commercial diesel sample were demonstrated using the system under both temperature programmed GC (TPGC) and thermal gradient GC (TGGC) conditions. TGGC analysis of a complex essential oil sample was also demonstrated. Addition of a secondary heater and polyimide insulation proved to be helpful in achieving the desired elution temperature without having to raise the primary heater temperature above 300°C for high boiling point compounds.

Construction and application of a cold on-column injection system for capillary gas chromatography

The Design of Resistive-Heating System for Capillary Column

A Quantitative Gas Stream Splitting Injection System suitable for Use with Capillary Columns

Repetitive liquid injection system for inverse gas chromatography

Capillary gas chromatographic injection system for large sample volumes

Benefits of a special cooling system to improve precision and accuracy in non-vaporizing on-column injection procedures

Development of an automated high-temperature valveless injection system for online gas chromatography

Construction and Evaluation of a Low Cost Interface for the Determination of Elemental Speciation by Gas Chromatography Coupled to Inductively Coupled Plasma Mass Spectrometry (GC‐ICP‐MS)

Extending the upper temperature range of gas chromatography with all-silicon microchip columns using a heater/clamp assembly

Sample introduction in high speed capillary gas chromatography; input band width and detection limits

Fabrication of micro-gas chromatograph columns for fast chromatography

Electrically heated, air-cooled thermal modulator and at-column heating for comprehensive two-dimensional gas chromatography

Simultaneous three-dimensional gas-liquid chromatography on wall-coated glass-capillary columns

Valveless gated injection for microfluidic chip-based liquid chromatography system with polymer monolithic column.

Innovations in High-Pressure Liquid Injection Technique for Gas Chromatography: Pressurized Liquid Injection System

Improving the reproducibility of quantitative gas-liquid chromatography by modifying the injection system

Micro gas chromatography sample injector for the analysis of natural gas

Preparation, performance and special applications of glass capillary columns

Accurate Nano-Injection System for Capillary Gas Chromatography

A Pressure-Driven Capillary Electrophoretic System with Injection Valve Sampling.

Temperature-programmed Multicapillary Gas Chromatograph Microcolumn for the Analysis of Odorous Sulfur Pollutants