Abstract:We report here the first coupling of fast GC to IRMS, in a system capable of 250 ms peak widths (fwhm) at 1 mL/min flow rates, one-fifth as narrow as any previously reported GCC-IRMS system. We developed an optimized postcolumn interface that results in minimal peak broadening, using a programmable temperature vaporization injector in place of a rotary valve or backflush system to divert solvent, a narrow capillary combustion reactor followed by a cryogenic water trap with narrow-bore (< 0.20 mm We transfer lines, and a narrow W. open split to the IRMS directly inserted into the column effluent. Quantitative combustion was demonstrated with CH4 injections. A comparison of CO2 injections with different fwhm peak widths (250, 2500, and 7500 ms) showed similar precisions, SD(delta C-13) = 0.2-0.3 parts per thousand, for injections of > 600 pmol C on column; precision for the narrow peaks (250 ms) was considerably better for injections < 150 pmol C on column. SD(delta C-13) < 1 parts per thousand was achievable for injections of 5-15 pmol on column for 250 ms wide peaks, 10-fold better precision than 2500 ms wide peaks, and within a factor of 3 of the counting statistics Emit For a mixture of 15 fatty acid methyl esters (FAME), 1.5 nmol C of each on column yielded typical SD(delta C-13(pdb)) = 0.4 parts per thousand for fast GC and 0.5%o for conventional GC. For 14 of the 15 FAME, delta C-13 values between the two systems were within 1.5 parts per thousand and not significantly different Fast GCC-IRMS required one-third the run time (450 s vs 1400 s) to achieve comparable resolution. Mean peak widths for fast GCC-IRMS of the FAME were 720 ins, compared to 650 ms by fast GC with flame ionization detection. At a 15-fold dilution (100 pmol C on column for each FAME), fast GCC-IRMS achieved -2-fold better precision and accuracy than similar injections on conventional GCC-ERMS. Finally, a mixture of 10 steroids (similar to 7 nmol C (100 ng) each on column) was analyzed with mean precision of SD)(delta C-13) = 0.2 parts per thousand in 620 s by fast GCC-IRMS, while conventional GCC-IRMS required 1200 s and achieved poorer resolution. delta C-13 values for the two system were similar (Delta delta C-13 <=:5 2 parts per thousand for all steroids), indicating that accuracy is not compromised. In summary, fast GCC-IRMS can achieve similar precision to conventional GC with considerable time savings for standard sample sizes (> 1 nmol C) and achieves modest precision (similar to 1 parts per thousand) near the counting statistics limit on low level components.

Capillary gas chromatographic injection system for large sample volumes

Repetitive liquid injection system for inverse gas chromatography

A Quantitative Gas Stream Splitting Injection System suitable for Use with Capillary Columns

Sample introduction in high speed capillary gas chromatography; input band width and detection limits

Micro gas chromatography sample injector for the analysis of natural gas

High-Throughput Capillary Liquid Chromatography Using a Droplet Injection and Application to Reaction Screening

Innovations in High-Pressure Liquid Injection Technique for Gas Chromatography: Pressurized Liquid Injection System

Simultaneous three-dimensional gas-liquid chromatography on wall-coated glass-capillary columns

Improving the reproducibility of quantitative gas-liquid chromatography by modifying the injection system

Construction and application of a cold on-column injection system for capillary gas chromatography

Development of an automated high-temperature valveless injection system for online gas chromatography

Quantitative Sample Injection for Capillary Electrophoresis

Accurate Nano-Injection System for Capillary Gas Chromatography

Taguchi Experimental Design Study of Very Large Sample Injection of Pesticides in Capillary Gas Chromatography

Role of the retaining precolumn in large-volume on-column injections of volatiles to gas chromatography

A Pressure-Driven Capillary Electrophoretic System with Injection Valve Sampling.

Dual-Column Stopped-Flow GC Method for Quantification of Permanent Gases, Water, and Organic Acids from a Single Injection

Valveless gated injection for microfluidic chip-based liquid chromatography system with polymer monolithic column.

Fast gas chromatography combustion isotope ratio mass spectrometry.

Quantitative analysis of 68 polar compounds from ten chemical classes by direct aqueous injection gas chromatography

Compact, Automated, Inexpensive, and Field-Deployable Vacuum-Outlet Gas Chromatograph for Trace-Concentration Gas-Phase Organic Compounds