Abstract:The surface preparation is a prerequisite for ensuring the required properties of a diamond film formed by gas-phase deposition. The influence of the temperature and concentration of the CuSO 4 etchant on the structural and phase compositions of the surface of hard-alloy materials is considered in this work, and the structural and phase compositions of a continuous polycrystalline diamond film at its growth stages is also considered. The adhesion of the diamond films to the surface of hard-alloy materials is determined qualitatively. It is established that the treatment of the hard-alloy surface in the CuSO 4 solution at t = 23°C leads to the inhomogeneous removal of a cobalt binder with chipping WC grains and the formation of the porous structure in the surface layer of the WC–6% Co alloy. The treatment by the CuSO 4 etchant at t = –2°C provides the homogeneous etching of the Co binder over the boundaries of WC grains and the formation of a chemically homogeneous surface. The orientation growth and adhesion of the diamond film depend on the elemental composition of the WC–Co alloy surface after treatment by the CuSO 4 solution. If the treatment was performed at t sln = 23°C, then the removal of copper from the defect surface WC layer is complicated during the synthesis, which provides the multidirectional growth of diamond crystals in the film along two directions, 〈111〉 and 〈110〉, which causes critical biaxial compressive stresses (2.5 GPa) and leads to low film adhesion to the hard alloy surface. If the treatment is performed at t sln = –2°C, then the orientational growth of diamond crystals in the film occurs in one preferential crystallographic direction 〈111〉, which lowers the biaxial compressive stresses (1.7 GPa) and increases the adhesive bond of the film to the hard alloy surface. The structure imperfection calculated from the ratio of the lines of integrated intensities I 1333 / I 1580 using the Raman spectroscopy method decreases with an increase in concentration at negative temperatures and increases at positive temperatures of the CuSO 4 solution during surface preparation.

Diamond growth on Fe-Cr-Al alloy by H2-plasma enhanced graphite etching

Metal dusting, carburization and diamond deposition on Fe–Cr alloys in CH 4 –H 2 plasma atmospheres

Direct coating adherent diamond films on Fe-based alloy substrate: the roles of Al, Cr in enhancing interfacial adhesion and promoting diamond growth

Deposition of Microcrystalline Diamond Films in H2 Microwave Plasma with Graphite Powder As Hydrocarbon Precursor

Diamond Films and Particles Growth in Hydrogen Microwave Plasma with Graphite Solid Precursor: Optical Emission Spectroscopy Study

High-selectivity Anisotropic Etching of Single-Crystal Diamond by H Plasma Using Iron Catalysis

Diamond Grown on Steel Via In-Situ Formed Interlayers

The Structural Evolution Of Nanocrystalline Diamond Films Synthesized By R.F. Pecvd

Diamond-Like Carbon Thin Films Deposited On Ti6al4v Alloy Surface By Plasma Gun At Atmospheric Pressure

Deposition of an adherent diamond film on stainless steel using Cr/CrAlN as an interlayer

Low-Temperature Growth Of Ultra-Thin Nano-Crystalline Diamond Films By Hfcvd In A Ch4/H-2 Mixture

Microwave plasma CVD of diamond films on high concentration alloys: Microstructure, hardness and wear properties

Structure and Properties of a High-Entropy AlCrFeCoNi Alloy after Treatment with an Electron–Ion Plasma

Growth of Nanocrystalline Diamond Films on Co-Cemented Tungsten Carbide Substrates by Hot Filament CVD

Enhanced Nucleation and Growth of Diamond Film on Si by CVD Using a Chemical Precursor

Effects of aluminum additive on diamond crystallization in the Fe-Ni-C system under high temperature and high pressure conditions

Diamond Micropowder Synthesis Via Graphite Etching in a Microwave Hydrogen Plasma

Experimental Study of Diamond-like Carbon Film on Aermet100 Steel and First-Principles Calculation of Interfacial Adhesion

The Metallization and Interface Reaction Between Diamond Particle and Cr Layer

Growth Features of Diamond Films on the Tungsten Carbide Surface with a Copper Sublayer

Grinding performance of electroplated diamond tools strengthened with Cr-C deposit using D-150 diamond particles