Abstract:<p>Low mechanical strength, especially at high temperatures, is the key problem that limit the application of FeCrAl alloys as the accident tolerance fuel (ATF) cladding materials. Dispersion strengthening by carbide nanoparticles is an effective way to improve mechanical properties at high temperatures. In this work, an ultrafine grained FeCrAl-0.6 wt.% ZrC alloys with excellent mechanical properties were fabricated successfully by mechanical milling and spark plasma sintering. The effect of milling speed on powder characteristics, microstructure and mechanical properties of FeCrAl alloys were investigated. The particle size of the powders increase significantly after milling at 400 rpm, while it has a lower oxygen content. Increasing the milling speed decreased the resultant grain size and improved relative density. Transmission electron microscope (TEM) demonstrated the nano ZrC particles uniformly distributed in the matrix at higher milling speed, which effectively promotes grain refinement and dispersion strengthening. The results of mechanical properties show that the tensile strength, percentage elongation and hardness of FeCrAl-0.6 wt.% ZrC alloys at room temperature (RT) reached up to 1.05 GPa, 349.86 HV and 12.1%, respectively, after milling at 400 rpm. It is worth noting that the FeCrAl-0.6 wt.% ZrC alloy also exhibited a good high-temperature strength more than 110 MPa at 800 ℃, which is about 55.4% and 24.7% higher than previously reported FeCrAl-0.5 wt.% ZrC and FeCrAl-1.0 wt.% ZrC alloys, but the plasticity is reduced. The results demonstrated that the excellent mechanical properties were not only attributed to the dispersion strengthen by nanosized ZrC, a good interface bonding between Fe matrix and nanosized ZrC, but also the ultra-fine grained structure induced by the milling process.</p>

Metal dusting, carburization and diamond deposition on Fe–Cr alloys in CH 4 –H 2 plasma atmospheres

Diamond growth on Fe-Cr-Al alloy by H2-plasma enhanced graphite etching

Experimental Study and Computer Simulation on Multicomponent Diffusion in Multiphase Dispersions During Solid Carburizing of HP40Nb and KHR45A Alloys

Preparation of Al-Cr-Fe Coatings by Heat Treatment of Electrodeposited Cr/Al Composite Coatings

Carburization of Three Fe-19Ni-21Cr-xAl (x = 0, 2, 6 At.%) Alloys at 900 °C in Oxygen-Contaminated CH4/H2 Atmospheres

Effect of 4 wt.% Cr on microstructure, corrosion resistance and tribological properties of Fe3Al-20 wt.%Al2O3 composites

Effect of Cr on Microstructure, Mechanical Properties, and Wear Behavior of in Situ 20 Wt.%al2o3/fe-25Al Composites

Microstructure evolution and high temperature air oxidation behaviour of thick Cr coatings at 1200°C

Effect of Chromium on Microstructure and Wear Resistance of Fe-Cr-C Hardfacing Alloys

The effect of Cr content on intragranular κ-carbide precipitation in Fe-Mn-Al-(Cr)-C low-density steels: A multiscale investigation

Influence of Ti on the Microstructure and Performance of Fe-Cr Alloy Cladding Layer

Tribological Behavior of In-Situ (cr, Mo)/Fe3al-20 Wt.%Al2o3 Composites at Elevated Temperatures

Fabrication of ultrafine grained FeCrAl-0.6 wt.% ZrC alloys with enhanced mechanical properties by spark plasma sintering

Phase transformation and precipitation during solidification of FeCrAl alloy for automobile exhaust gas purifying systems

Microstructure, abrasive wear and corrosion characterisation of laser metal deposited Fe-30Cr-6Mo-10Ni-2.2C alloy

Direct coating adherent diamond films on Fe-based alloy substrate: the roles of Al, Cr in enhancing interfacial adhesion and promoting diamond growth

Modifying Cr/CrN Composite Structure by Fe Addition: Toward Manufacturing Cost-Effective and Tough Hard Coatings

Effect of Cr Content on Microstructure, Mechanical, and Corrosion Properties of CoCr X FeMnNi High-Entropy Alloys Fabricated by Selective Laser Melting

Microstructure and Surface Properties of Chromium-Doped Diamond-Like Carbon Thin Films Fabricated by High Power Pulsed Magnetron Sputtering

Exploring the high-temperature steam oxidation behaviors of the lean-Cr (7–10 wt%) FeCrAl alloys

Effect of different chromium contents on microstructure and two-body abrasive wear behavior of Fe-Mn-B surfacing alloys