Electroencephalography During Hemiarch Replacement With Moderate Hypothermic Circulatory Arrest.

J. Keenan,Hanghang Wang,A. Ganapathi,B. Englum,Emily B. Kale,Joseph P. Mathew,Aatif M. Husain,G. C. Hughes

DOI: https://doi.org/10.1016/j.athoracsur.2015.08.002

2016-02-01

Abstract:

What problem does this paper attempt to address?

Effect of Submicron SiC Particles on the Properties of Alcocrfeni High Entropy Alloy Coatings

Nanjing Agricultural University,Wang Tongyue,Wang Xianfa,Jiang Ye,Xue Jianxun,Liu Xiao,Jiang Yan,Chen Zhipeng

DOI: https://doi.org/10.1007/s11106-020-00176-z

2020-01-01

Powder Metallurgy and Metal Ceramics

Abstract:The high entropy alloy (HEA) coatings are potential candidates for advanced application in the protection of steel and other traditional alloys due to their excellent physical and mechanical performance. The AlCoCrFeNi alloy series were favorably studied due to comparably low cost and stable performance. In this research, the AlCoCrFeNi coatings were prepared through surface mechanical abrasion treatment (SMAT). The process implied the comprehensive effect of cold welding and friction. The submicron-size SiC particles were added into the raw materials in different amounts. For SMAT, a high-energy ball milling method was adopted to promote the alloying of metals, disperse SiCp, and combine the powder to the carbon steel substrate. Afterward, the phase composition, microstructure of coatings, and distribution of reinforcement were detected through XRD and SEM analysis, separately, and the effect of SiC particles content on the properties of the coatings was analyzed. The results show that the addition of submicron-sized SiC significantly improved the density and stiffness of the HEA coating and diminished defects and surface roughness. Сoatings containing SiC display enhanced adhesion force and wear resistance. The proposed mechanism is that the submicron SiC particles promoted mechanical alloying of pure metal and intensified the adherence and cold welding of the coating. Especially, herein, the addition of 15 wt.% SiC granted the best comprehensive properties of the coating. Excessive SiC content led to the deterioration of coating plasticity and the growth of cracks.
Diamond growth on Fe-Cr-Al alloy by H2-plasma enhanced graphite etching

Y. S. Li,A. Hirose

DOI: https://doi.org/10.1063/1.2717013

IF: 2.877

2007-04-01

Journal of Applied Physics

Abstract:Without intermediate layer and surface pretreatment, adherent diamond films with high initial nucleation density have been deposited on Fe–15Cr–5Al (wt. %) alloy substrate. The deposition was performed using microwave hydrogen plasma enhanced graphite etching in a wide temperature range from 370to740°C. The high nucleation density and growth rate of diamond are primarily attributed to the unique precursors used (hydrogen plasma etched graphite) and the chemical nature of the substrate. The improvement in diamond adhesion to steel alloys is ascribed to the important role played by Al, mitigation of the catalytic function of iron by suppressing the preferential formation of loose graphite intermediate phase on steel surface.

physics, applied
Deposition of an adherent diamond film on stainless steel using Cr/CrAlN as an interlayer

Xiao Li,Fan Xia,Chengcheng Wang,Chengke Chen,Meiyan Jiang,Jinping Pan,Shaohua Lu,Andrey A. Khomich,Igor Vlasov,Xiaojun Hu

DOI: https://doi.org/10.1016/j.surfcoat.2022.128960

IF: 4.865

2022-11-15

Surface and Coatings Technology

Abstract:Cr/CrAlN films were chosen as an interlayer to deposit an adherent diamond film on stainless steels by using hot filament chemical vapor deposition (HFCVD). The results show that diamond film with good adhesion is successfully deposited on 3Cr13 stainless steel when the interlayer with Al content from 0 to 18 at.%, which is ascribed to high chemical adhesion by a certain amount of chromium carbide. When Al content in the interlayer further increases, an excessive Al2O3 is formed on the surface of the interlayer, carbon supersaturation is easily arrived, so that the amount of the carbide at the diamond/interlayer interface decreases evidently. This decreases the strength of the covalent bonding from the carbide, producing poor adhesion. Moreover, with the raise of Al content in the interlayer, the hardness of the multilayer coated stainless steel increases due to the increase of the interlayer's hardness and the slight increase of the diamond content in the film.

physics, applied,materials science, coatings & films
Combined FISH and immunofluorescent staining methods to co-localize proteins and mRNA in neurons and brain tissue.

Bin Ma,N. Tanese

DOI: https://doi.org/10.1007/978-1-62703-411-1_9

Abstract:
Spin-polarized DFT calculations of elemental effects on hydrogen atom adsorption on FeCrAl (110) surface

Xiaojing Li,Yu Ma,Wenzhong Zhou,Zhao Liu

DOI: https://doi.org/10.1016/j.apsusc.2021.152273

IF: 6.7

2022-01-01

Applied Surface Science

Abstract:FeCrAl alloys, due to their high-temperature oxidation resistance and excellent mechanical properties, are considered as one of the most promising substitutes of the current Zirconium alloy as cladding in light water reactors. Hydrogen generation is an inevitable phenomenon in nuclear reactors, and hydrogen diffusion and retention in the cladding material would cause the deterioration of the mechanical and oxidation-resistant properties. Understanding hydrogen adsorption is of great importance for studying the whole diffusion mechanism. In this paper, spin-polarized density functional theory (DFT) calculations were conducted to investigate the H atom adsorption on the (110) surface of pure body-centered cubic structure (BCC) Fe, Cr, Al and FeCrAl. Different initial positions (top and three-fold sites) were calculated to assess how the three elements (Fe, Cr, Al) affect H adsorption. The results show that there are strong elemental effects of Cr and Al on H adsorption. H cannot be adsorbed at the top site of FeCrAl surfaces but it is stably adsorbed at the three-fold sites consisting of the Fe and Cr atoms. However, no H adsorption occurs at the three-fold site containing the Al atoms due to their charge deficiency. According to the charge density difference analyses, Al atoms influence the adsorption of FeFe-Cr and Fe-Cr-Cr sites mainly by influencing the interactions between Cr and H.
The Metallization and Interface Reaction Between Diamond Particle and Cr Layer

YF Zhu,L Wang,WQ Yao,LL Cao

DOI: https://doi.org/10.3321/j.issn:0251-0790.2000.08.019

2000-01-01

Abstract:A Cr layer with thickness of 150 nm was successfully deposited on the surface of diamond particles using DC magnetron sputtering technique, The interface diffusion and reaction between Cr and diamond was promoted by annealing in the range from 300 degrees C to 600 degrees C in high vacuum. The Auger profile results showed that the width of interface layer was more than 90 nm, A Cr2C carbide layer was formed after Cr/diamond annealed above 500 degrees C, The formation of Cr2C on the interface was confirmed by Auger line shapes. When the annealing temperature was below 500 degrees C and annealing time less than 4 h, Cr2C3 interface species was formed. Higher temperature and longer time resulted in Cr2C interface species. The chemical reaction suggested that there was a strong chemical bond on the interface of Cr/diamond, which was one of the important factors for the high adhesion strength between metal and diamond. The interface diffusion and reaction was governed by the diffusion of carbon from diamond substrate, The activation energy of the interface diffusion reaction was 38.4 kJ/mol, The interface species varied with annealing temperature and time.
Diamond-like Carbon Film on 20 CrNiMo Steel Prepared by Hollow-Cathode Glow Discharge

CHEN Fei,CHEN Jia-qing,ZHOU Hai,ZHANG Yue-fei

DOI: https://doi.org/10.13289/j.issn.1009-6264.2011.03.003

2011-01-01

Abstract:Diamond-like carbon(DLC) thin film was deposited on the surface of 20CrNiMo alloy by hollow cathode glow discharge technique.High purity graphite was selected as the cathode and Ar as working gas.The structure of the DLC thin film was analyzed by laser Raman spectroscopy.Surface morphology of the film was observed by atomic force microscope(AFM).The adhesion between the DLC thin film and the substrate was investigated with scratch testing.The morphology of the scratch was observed by scanning electron microscopy(SEM).Friction and wear behavior of the DLC thin film under dry sliding against GCr15 steel was evaluated on a ball-on-disc test rig.The results show that it is feasible to prepare a DLC thin film of 0.6 μm thick by this experimental process.The surface roughness Ra of the film is 7-8 nm.The DLC thin film has a good adhesion with critical load of 52 N by scratch testing.Excellent friction and wear-resistant behavior of the film is observed.Friction coefficient of the 20CrNiMo substrate is about 0.50 under dry sliding against steel,while the DLC thin film exhibited much lower friction coefficient of 0.15 under the same testing condition.
High adhesion diamond films deposited on stainless steel by using nanocomposite films with mosaic interface as an interlayer

Feng Lyu,Xiao Li,Chengke Chen,Cheng Liu,Chuanxing Li,Meiyan Jiang,Xiaojun Hu

DOI: https://doi.org/10.1016/j.apsusc.2020.146916

IF: 6.7

2020-10-01

Applied Surface Science

Abstract:It suffers from poor adhesion to deposit diamond films on steel by using normal metal compound films as an interlayer. Here, high adhesion diamond films were successfully prepared on stainless steel by using Cr/CrSiN nanocomposite film as interlayer. The results show that with Si contents increasing to 10.6 at.%, spikes appear at the interface between diamond films and interlayer, exhibiting high adhesion with hardness increasing to 80 GPa. With Si contents further increasing to 15.5 at.%, the spikes disappear and diamond film peels off even though its hardness still keeps 62 GPa. This indicates that spikes, composed of Cr-C compounds, supply mosaic structure and mechanical lock effects to improve the adhesion. The spikes' composition means that carbon atoms react with Cr/CrNx crystals in interlayer during HFCVD. Under lower Si contents, amorphous SiNx/Si phases are few, Cr/CrNx crystals can easily react with carbon atoms via different velocities, causing the co-existence of longer and shorter Cr-C phase to form the spikes. As Si content increases, more amorphous phases envelop the crystals, limiting the reaction of carbon atoms with Cr/CrNx crystals, so the spikes disappear. This supplies a way to control the adhesion of diamond films by adjusting Si contents to produce different interface structures.

chemistry, physical,physics, applied, condensed matter,materials science, coatings & films
Effect of Fe on the formation of NiAl intermetallic light beam surfacing layer and its microstructure

Di Zhang,Jiguo Shan,Wuzhu Chen,Jialie Ren

DOI: https://doi.org/10.3321/j.issn:1002-185x.2006.01.002

2006-01-01

Rare Metal Materials and Engineering

Abstract:With the use of X-ray diffraction, SEM and EDS, the effect of iron element on the formation of NiAl intermetallic light beam surfacing layer and its microstructure were investigated. The results show that owing to the high melting point of NiAl intermetallic, NiAl surfacing is difficult to acquire by light beam heating Ni and Al mixed powder. Adding reasonable content of Fe powder (11at%similar to 28at%) to Ni and Al mixed powder can decrease the melting point of surfacing alloy system and improve the formation of light beam surfacing layer. With the increase of Fe addition in surfacing material, the dilution of surfacing layer and its Fe content firstly increase and then decrease. Too high addition of Fe powder (43at%) makes surfacing metal not to wet base metal. The Fe in surfacing layer promotes the precipitation of strip Fe3Al, and the precipitation proportion of strip Fe3Al increases with the increase of Fe content in surfacing layer. The light beam surfacing layer consists of NiAl column crystal and strip Fe3Al between column crystal.
Effects of Slurry Composition and Interfacial Adhesion of Monolithic Coatings on FeCrAl Honeycombs

Yanlun Ren,Hong Xu,Li Zhang

DOI: https://doi.org/10.3390/coatings14111372

IF: 3.236

2024-10-29

Coatings

Abstract:Excellent coating adhesion is a crucial requirement for monolithic catalysts. Within this investigation, a Design of Experiments (DOEs) Taguchi approach was leveraged to construct a 9-factor-3-level matrix encompassing 27 parallel experiments. This framework was employed to scrutinize the pivotal elements influencing the adhesion of FeCrAl metal-based integral coatings, which were prepared using the slurry method. Moreover, an unprecedented endeavor was made to scrutinize the mechanism of coating delamination from the vantage points of macroscopic slurry, microscopic coatings, and nanoscale interfaces. The findings reveal the following: (1) The inclusion of a high-acidity additive (>5%) emerges as one of the pivotal factors in achieving superior adhesion, particularly when the boehmite content exceeds 1%. (2) The existence of binder-filled interstices within the coating, smaller by 1–2 orders of magnitude than the carrier particles, significantly contributes to heightened adhesion. (3) A bonding region of approximately 5 nm is present at the interfaces between carrier particles, resulting in augmented adhesion.

materials science, multidisciplinary,physics, applied, coatings & films
Improved Interfacial Adhesion Between TiAlN/DLC Multi-Layered Coatings by Controlling the Morphology Via Bias

Liangliang Liu,Zhongzhen Wu,Xiaokai An,Tielei Shao,Shu Xiao,Suihan Cui,Hai Lin,Ricky K. Y. Fu,Xiubo Tian,Paul K. Chu,Feng Pan

DOI: https://doi.org/10.1016/j.surfcoat.2017.10.029

IF: 4.865

2017-01-01

Surface and Coatings Technology

Abstract:By combining the advantages of the thermo-mechanical properties of TiAlN and self-lubricating properties of diamond-like carbon (DLC), a multi-layered TiAlN/DLC coating is fabricated by filtered cathodic vacuum arc and magnetron sputtering. According to the different morphology and mismatch between the physical and chemical properties of TiAlN and DLC, multiple methods are used to study the growth mechanism of crystalline TiAlN and amorphous DLC in the combined system. The morphology evolution depending on the bias is studied and the brittle interface is assessed by scratch experiments. The results show that an interlamination failure occurs at the top of first DLC layer due to the cluster morphology obtained by small bias, however, the failure moves to the interface above the substrate when the clusters are refined by increasing bias. By adopting the stepwise decreased bias, the 4.5μm thick TiAlN/DLC multi-layer coating is fabricated and does not exhibit interfacial failure at any interface between TiAlN and DLC in the scratch experiments up to a load of 100N. Excellent adhesion (Lc=63N) is also achieved from coatings deposited on high-speed steel with optimized Cr/CrCx/CrC interlayers prepared by high-power impulse magnetron sputtering.
Deposition of diamond film on steel substrate by precoating an intermediate layer

Zhiqing Chen,Zhidong Gao,Xiaoshu Zeng,Ji Liang,Binqing Wei,Dehai Wu

1996-01-01

Abstract:Diamond films have been deposited on carbon steel with an intermediate layer by chemical vapor deposition (CVD). Diamond coatings on steel substrates are interesting for potential applications, but there are at least three serious problems: a long nucleation period, the catalytic effect of iron, and thermal expansion mismatch. An intermediate layer was used to block carbon diffusion, enhance adhesion and suppress SP2 carbon precipitation. We report the research on the deposition of diamond films on steel substrates without a buffer layer, and copper coated/silicon coated steel substrates, respectively. By scanning electron microscopy (SEM), Raman spectroscopy and scratch test, it is show that precoating a silicon intermediate layer is an efficient method for deposition of diamond films on steel substrates.
Tribological Properties of Graded Diamond-Like Carbon Films on Ti Ion-Implanted Aluminum Substrate

Ming Xu,Xun Cai,Yourning Liu,Shihao Pu,Paul K. Chu

DOI: https://doi.org/10.1016/j.diamond.2007.12.025

IF: 3.806

2008-01-01

Diamond and Related Materials

Abstract:Titanium ions are implanted into the aluminum substrate prior to deposition of the Ti interlayer and DLC graded film produced by magnetron sputtering in order to enhance the structural continuity between the soft substrate and graded DLC film. The Ti-implanted substrate not only strengthens loading support but also improves adhesion with the overlying film. The total thickness of the functionally graded film on the Al substrate reaches over 10 pm and it has a hardness value of similar to 11 GPa. The graphitic network in DLC film helps to reduce the friction coefficient while the graded design disperses the stress during wear and loading. (C) 2007 Elsevier B.V. All rights reserved.
Study on the Performance of Fe-Based Alloy Coating on 40Cr Substrate Surface

Chao Chen,Qiaofeng Bai,Qihang Li,Chunjiang Zhao,Jian Zhang,Shuai Zhang

DOI: https://doi.org/10.1007/s11665-024-09157-4

IF: 2.3

2024-01-25

Journal of Materials Engineering and Performance

Abstract:In this work, Fe-based alloy coatings with different elemental ratios were prepared on the surface of 40Cr steel using high-speed laser melting. The coatings' microstructure, microhardness, wear resistance and corrosion resistance were compared and analyzed. According to the analysis of XRD and SEM results, the specimen with higher Cr content b has finer and denser grain size and structure compared to the sample with higher Ni content a. Fine grain strengthening and solid solution strengthening increased the hardness of the coating by 41.5 and 57.5%, respectively, compared to the substrate. Supported by high hardness, the wear mechanism changes from adhesive wear on the substrate surface to abrasive wear on the coating surface, eventually producing a compacted friction layer on the coating surface, decreasing wear. The electrochemical corrosion results showed that the corrosion potential and corrosion current density of specimen a were − 0.221 V and 5.623 × 10 −6 (A/cm 2 ), and the corrosion potential and corrosion current density of specimen b were − 0.314 V and 2.914 × 10 −6 (A/cm 2 ). Cr contributes to the formation of the passivation film; while, Ni and Mo contribute to its stability and denseness.

materials science, multidisciplinary
The Study of Interface Diffusion and Reaction Between Cr and Diamond Deposited by Magnetron Sputtering Technigue

ZHU Yong-fa,WANG Li,YAO Wen-qing,CAO Li-li

DOI: https://doi.org/10.3969/j.issn.1001-4381.2000.01.006

2000-01-01

Abstract:A Cr layer with thickness of 150nm was successfully deposited on the surface of diamond particles using DC magnetron sputtering technique. The interface diffusion and reaction between Cr layer and diamond substrate have been studied using AES depth profile and line shape analyses. The results show that interface diffusion and reaction take place during the deposition of Cr layer. The Cr atoms diffuse into diamond substrate, and react with carbon atom in diamond to form carbide on the interface. The interface diffusion and reaction result from the impact of Cr atoms which keep an energy of 3~4eV. The interface diffusion and reaction can be promoted significantly by raising the sputtering power.
Adhesion and friction behaviors of a γ-Fe/diamond heterogeneous contact interface: a density functional theory study

Qizhen He,Lixiang Rao,Wenwei Song,Hailiang Liu,Silong Zhang,Xuejun Ren,Qingxiang Yang

DOI: https://doi.org/10.1039/d3cp01333b

2023-08-16

Abstract:Diamond tools play a vital role in precision machining. However, the adhesive wear restricts their application when Fe-based workpieces are cut by diamond tools. Thus, it is significant to theoretically explain the interface binding mechanism between the diamond and Fe alloy matrix. In this study, the adhesion and friction behaviors of a γ-Fe/diamond (denoted as Fe/C) heterogeneous contact interface were investigated employing density functional theory (DFT). The results show that the transfer of the Fe atom to C atom occurs when the interaction energy for a given configuration is larger than the separation energy of the corresponding Fe surface layers. The energy barriers of the Fe/C(100), (110) and (111) sliding interfaces along the minimum energy path are 1.45, 0.48 and 0.42 J m-2, respectively, indicating that the Fe/C(111) interface is the easiest to slide. Furthermore, the friction potential barrier increases with an increase in the load (1-5 nN) according to the potential energy curves. Moreover, the friction coefficient of the Fe/C interface is larger than 0.2 and provides a theoretical minimum friction coefficient for the Fe/C sliding interface.
Excellent Adhered Thick Diamond-Like Carbon Coatings by Optimizing Hetero-Interfaces with Sequential Highly Energetic Cr and C Ion Treatment

Liangliang Liu,Zhongzhen Wu,Xiaokai An,Shu Xiao,Suihan Cui,Hai Lin,Ricky K. Y. Fu,Xiubo Tian,Ronghua Wei,Paul K. Chu,Feng Pan

DOI: https://doi.org/10.1016/j.jallcom.2017.11.057

IF: 6.2

2017-01-01

Journal of Alloys and Compounds

Abstract:Diamond-like carbon (DLC) coatings have attracted much attention due to their excellent hardness, low friction, and superior corrosion resistance. Unfortunately, the poor adhesion caused by internal stress limits the typical thickness to below 3-5 mu m. This paper presents a novel interlayer design and interface engineering and the induced excellent adhesion of thick diamond-like carbon (DLC) coatings on a high speed steel substrate. The interlayer has fundamentally a graded Cr/CrCx/CrC/DLC structure, but various treatments to the hetero-interfaces have been conducted including sequential energetic ion bombardments with Cr at the substrate/Cr interface using high-power impulse magnetron sputtering (HiPIMS) and with C at the CrC/DLC interface using an anode layer ion source. It has been observed that the critical load has been improved from 18 N for a single Cr interlayer to 77 N for a Cr/CrCx/CrC interlayer for thick DLC coatings of 13 mu m. Using the same design, a very high critical load of 73 N has been achieved on the ultra-thick DLC coating of 50 mu m. This interlayer design has allowed the deposition of a DLC coating that is not only thick but also hard with excellent tribological properties. The DLC coatings have a high hardness of > 18 GPa, a low friction coefficient of 0.12 and a low wear rate of (1.7 +/- 0.2) x 10(-15) m(3)/N.m. This paper discusses the effect of the ion bombardment of the interlayer on the coating adhesion and the strengthening mechanisms. (C) 2017 Elsevier B.V. All rights reserved.
Achieving superlubricity and high adhesion strength of hydrogenated amorphous carbon film with Al/Cr/Si-doping

Quansheng Ma,Yongqiang Fu,Yi Xu,Tianbao Ma

DOI: https://doi.org/10.1016/j.carbon.2023.118424

IF: 10.9

2023-01-01

Carbon

Abstract:Excellent tribological properties of hydrogenated amorphous carbon films make it an important candidate for friction reduction in industry. However, the great challenge of achieving both high adhesion strength and super-low friction limits its wide applications. In this work, a novel Al, Cr and Si co-doped hydrogenated amorphous carbon (AlCrSi/a-C:H) film was prepared by high-power impulse magnetron sputtering (HiPIMS) method. The AlCrSi/a-C:H film showed favorable mechanical performance and high adhesion (similar to 80 N), which was attributed to the controlled elements doping and special transition layers produced by HiPIMS method. Meanwhile, superlubricity was obtained with coefficient of friction 0.0014. Detailed characterizations suggested that doping elements played significant roles in tribo-chemical reactions during friction. On one hand, doping elements can promote shear-induced graphitization and formation of graphite-like layers at the friction interface. On the other hand, the preferential oxidation of doping elements can protect the formed graphite-like layers from oxidation and the formed oxides nanoparticles can also be wrapped by carbon layers to prevent abrasive wear. It was the synergistic effects of graphitization and oxidation actions that led to superlubricity state of the film. The proposed AlCrSi/a-C:H film architecture with strong adhesion and superlubricity properties provides design criteria of superlubricious films for industrial applications.
Enhanced adhesion of diamond-like carbon films with a composition-graded intermediate layer

Q.R. Hou,J. Gao

DOI: https://doi.org/10.1007/s003390050900

1999-01-01

Applied Physics A

Abstract:Adherent diamond-like carbon films were deposited on silicon substrates by the pulsed laser deposition method under a magnetic field. A composition-graded intermediate layer with a composition gradient from the substrate to the film was used to enhance the adhesion. It was found that adhesion was dependent on the thickness and composition gradient of the intermediate layer. For diamond-like carbon films deposited at room temperature, intrinsic stress in the interlayer played a key role. When an intermediate layer with a thickness of about 103 nm was used, the intrinsic stress was maximum and adhesion was poor. For films deposited at 60 degrees C and 100 degrees C, thermal stress and intrinsic stress should be considered together. Very thin intermediate layers (approximate to 34 nm) were not suitable for good adhesion due to the presence of thermal stress. Adhesion was poor when the thickness of the intermediate layer was about 178 nm owing to imposition of the intrinsic stress. A composition profile with an exponent greater than 1 (silicon-riched) was beneficial to good adhesion.
Interface diffusion and reaction between Cr layer and diamond particle during metallization

Yongfa Zhu,Li Wang,Wenqing Yao,LiLi Cao

DOI: https://doi.org/10.1016/S0169-4332(00)00555-9

IF: 6.7

2001-01-01

Applied Surface Science

Abstract:A Cr layer with a thickness of 150nm was successfully deposited on the surface of diamond particles using the dc magnetron sputtering technique. AES analysis indicated that the Cr layer reacted with diamond particle to form Cr2C3 carbide species on the interface during the deposition. With the rising of deposition power, the interface diffusion between Cr layer and diamond substrate increased. The interface diffusion and reaction between the Cr layer and diamond substrate were promoted significantly by an annealing treatment at a temperature range from 300 to 600°C in a ultrahigh vacuum (UHV). When the annealing temperature was below 500°C and annealing time was less than 4h, CrC carbide species were formed on the interface. Higher temperature and longer time resulted in a Cr2C carbide interlayer. The carbide species of Cr2C was resulted from the interface diffusion and reaction which can be intensified significantly with raising the annealing temperature and time. The depletion of carbon atoms from diamond substrate and the diffusion of carbon controlled the formation of carbide layer. The apparent activation energy of interface diffusion and reaction was about 38.41kJ/mol. The interface diffusion and reaction can be impeded by low vacuum.

Electroencephalography During Hemiarch Replacement With Moderate Hypothermic Circulatory Arrest.

Effect of Submicron SiC Particles on the Properties of Alcocrfeni High Entropy Alloy Coatings

Diamond growth on Fe-Cr-Al alloy by H2-plasma enhanced graphite etching

Deposition of an adherent diamond film on stainless steel using Cr/CrAlN as an interlayer

Combined FISH and immunofluorescent staining methods to co-localize proteins and mRNA in neurons and brain tissue.

Spin-polarized DFT calculations of elemental effects on hydrogen atom adsorption on FeCrAl (110) surface

The Metallization and Interface Reaction Between Diamond Particle and Cr Layer

Diamond-like Carbon Film on 20 CrNiMo Steel Prepared by Hollow-Cathode Glow Discharge

High adhesion diamond films deposited on stainless steel by using nanocomposite films with mosaic interface as an interlayer

Effect of Fe on the formation of NiAl intermetallic light beam surfacing layer and its microstructure

Effects of Slurry Composition and Interfacial Adhesion of Monolithic Coatings on FeCrAl Honeycombs

Improved Interfacial Adhesion Between TiAlN/DLC Multi-Layered Coatings by Controlling the Morphology Via Bias

Deposition of diamond film on steel substrate by precoating an intermediate layer

Tribological Properties of Graded Diamond-Like Carbon Films on Ti Ion-Implanted Aluminum Substrate

Study on the Performance of Fe-Based Alloy Coating on 40Cr Substrate Surface

The Study of Interface Diffusion and Reaction Between Cr and Diamond Deposited by Magnetron Sputtering Technigue

Adhesion and friction behaviors of a γ-Fe/diamond heterogeneous contact interface: a density functional theory study

Excellent Adhered Thick Diamond-Like Carbon Coatings by Optimizing Hetero-Interfaces with Sequential Highly Energetic Cr and C Ion Treatment

Achieving superlubricity and high adhesion strength of hydrogenated amorphous carbon film with Al/Cr/Si-doping

Enhanced adhesion of diamond-like carbon films with a composition-graded intermediate layer

Interface diffusion and reaction between Cr layer and diamond particle during metallization