Abstract:This paper proposes a chromium oxide (Cr 2 O 3 ) gel abrasive tool with the coated aluminum nitride (AlN) powder to give the tool with self-sharpening ability. The SiO 2 /AlN powder (S/A powder) is prepared through the sol–gel method. Effect of acetic acid solution content on the Tetraethyl orthosilicate (TEOS) hydrolysis reaction is explored. Effect of sintering temperature on the moisture resistance of the S/A powder are studied. The viscosity experiments, porosity tests, pre-grinding experiments and hardness tests are conducted to test the properties of the abrasive tool. The force–displacement curves are tested to evaluate the uniformity of the tool. The grinding effect on the sapphire substrate of tool with S/A powder, normal abrasive tool and tool with pore forming agent are compared. Results show that the SiO 2 gel has great stability when the acetic acid solution content reached 0.6 g, and the gel does not crack after a week's rest, which is suitable for the coating of the AlN powder. In the powder sintering experiment, 700 °C is found to be the optimal sintering temperature for the S/A powder preparation. The viscosity experiments show that the viscosity of the slurry will surge when the content of S/A powder reached 12 wt%, which impairs the uniformity of the gel abrasive tool. In the pre-grinding test, the abrasive tool with the S/A powder of 9 wt% shows great grinding stability, material removal rate (MRR) and wear resistance. The grinding experiments show that tool with S/A powder can achieve better surface quality and have a stable grinding process, and the glazing phenomena is ameliorated. After grinding, the average roughness R a of the sapphire substrate reaches 1.57 nm and its flatness reached 0.725 μm. After chemical mechanical polishing (CMP), the average R a of sapphire substrate reaches 0.64 nm and the scratch-free surface can be obtained.

Grinding performance of electroplated diamond tools strengthened with Cr-C deposit using D-150 diamond particles

Effect of ultrasonic on properties of electroplated diamond tools

Application of Magnetron Sputter Ion Plated CrAlTiN Composite Coating in Improving Wear Resistance of Milling Cutter

Fabrication and evaluation of high-entropy alloy reinforced Fe bond diamond tool

Fabrication and use of Cu-Cr-diamond composites for the application in deep feed grinding of tungsten carbide

Investigation on abrasive wear of electroplated diamond belt in grinding nickel-based superalloys

Experimental Investigation of Fabricating Diamond Abrasive Layers by EDM

Diamond-like Carbon Film on 20 CrNiMo Steel Prepared by Hollow-Cathode Glow Discharge

Study on the Fabrication and Grinding Performance of the Self-sharpening Cr2O3 Gel Abrasive Tool

The Fabrication of Porous Metal-Bonded Diamond Coatings Based on Low-Pressure Cold Spraying and Ni-Al Diffusion-Reaction

A comparative study on FeAl and NiAl bonded diamond tools for dry grinding based on wear characteristics at elevated temperature

Cu-induced enhancement of interfacial bonding for brazed diamond grits with NiCr filler alloys

Strategy for achieving high-performance PVD nano-multilayered AlTiN/TiN coated milling tool: Fine platelet-grained WC–Co substrate and interface regulation

Preparation and performance study of electroplated Ni–W/diamond ultrathin dicing blades

Experimental Study on Diamond Abrasive Layer Fabrication by Electrical Discharge Surface Intensifying

Microstructure and Properties of the AlCrSi(O)N Tool Coatings by Arc Ion Plating

Mechanical and cutting performance of cemented carbide tools with Cr/x/DLC composite coatings

Enhancing Tool Performance in High-Speed End Milling of Ti-6Al-4V Alloy: The Role of AlCrN PVD Coatings and Resistance to Chipping Wear

Micro-Grinding of Electrochemically Pretreated Ultra-high-Chromium Steel

Fabrication and performance evaluation of metal bond diamond tools based on aluminothermic reaction

Comparative study on NiAl and FeAl intermetallic-bonded diamond tools and grinding performance for Si3N4 ceramic