Abstract:The most important advantage of additive manufacturing by laser powder bed fusion (PBF-LB) technique is the ability to produce geometrically complex parts, but the problem is their rough surfaces, often difficult or inaccessible to finish by machining. Therefore, research to improve the reproducibility of the mechanical behavior of parts manufactured from aluminum alloy powders with as-built surfaces is of vital importance for the aerospace and automotive industries. Since local notches occurring on rough surfaces after the PBF-LB process are unavoidable, the way to solve this problem is to obtain as-built surfaces of the highest possible quality and to adapt a post-process heat treatment that increases the ductility and fracture toughness of the material. To this end, the present work focused on the study of the mechanical performance of AlSi7Mg0.6 samples with a rough as-built surface in the as-built state and after several variants of post-process heat treatment, combined with a detailed analysis of the microstructures corresponding to these states. Tensile samples built on a platform preheated to 100 °C, achieved a relative density of 99.85%, satisfactory surface quality, a relatively low level of residual stress and moderate crystallographic texture. Despite the rough surface, the samples under the as-built condition and after different variants of heat treatment (direct aging (DA), stress relieving (SR), and solution annealing followed by artificial aging (T6)), achieved tensile properties comparable to those reported in the literature for PBF-LB samples with machined surfaces. The resulting combinations of tensile properties of PBF-LB samples after different heat treatment variants were evaluated using the quality index (QI) commonly used to assess the quality of heat-treated Al-Si-Mg castings. It was found that the proposed T6 treatment provides the best combination of strength properties and ductility, compared to those obtained after both DA and SR, as well as after T6 treatment of high-quality castings, from the point of view of reducing the sensitivity of AlSi7Mg0.6 alloy to surface roughness.

Wear Behavior of AlSi10Mg Alloy Produced by Laser‐Based Powder Bed Fusion and Gravity Casting

Effect of Aluminium Content and Processing Parameters on the Microstructure and Mechanical Properties of Laser Powder-Bed Fused Magnesium-Aluminium (0, 3, 6, 9wt%) Powder Mixture

Effect of build direction and surface finish on wear behavior of AlSi10Mg alloy casted by laser powder bed fusion

Fretting wear behavior on LPBF processed AlSi10Mg alloy for different heat treatment conditions

Influence of eutectic-Si in as-cast and fibrous-eutectic-Si in LPBF-processed AlSi10Mg alloys on wear and corrosion behaviors treated with direct aging route

High Temperature Wear Behavior of AlMgScZr Alloy Produced By Laser Powder Bed Fusion

Wear Behavior of a Heat-Treatable Al-3.5Cu-1.5Mg-1Si Alloy Manufactured by Selective Laser Melting

Tailoring heat treatment for AlSi7Mg0.6 parts with as-built surface generated by laser powder bed fusion to reduce surface roughness sensitivity

Microstructure and Wear Resistance of Laser-Treated and Slow Cooled AlSi10Mg-(x)Ni Alloys

Additive Manufacturing of Al-12Si Alloy by Powder Laser Bed Fusion: an Investigation into its Microstructural Processes Formation and its Effects on Mechanical Behavior

The Influence of Post-Treatment on Micropore Evolution and Mechanical Performance in AlSi10Mg Alloy Manufactured by Laser Powder Bed Fusion

Influence of Laser Energy Density on Tribological Properties of AlSi10Mg Manufactured by Selective Laser Melting

The AlSi10Mg Samples Produced by Selective Laser Melting: Single Track, Densification, Microstructure and Mechanical Behavior

Effect of heat treatments on microstructure and mechanical properties of AlSi10Mg alloys fabricated by laser powder bed fusion

Microstructure-induced anisotropic tribological properties of Sc-Zr modified Al–Mg alloy (Scalmalloy®) produced via laser powder bed fusion process

Fatigue behavior under variable amplitude loadings in AlSi10Mg alloy components produced by laser powder bed fusion

Comparative tribological studies of additive manufactured as-built and chemically polished AlSi10Mg alloy surfaces

An Experimental Investigation into the Dry Reciprocating Wear Behavior of Additively Manufactured AlSi10Mg Alloys

Mechanical Properties of AlSi10Mg Processed by Laser Powder Bed Fusion at Elevated Temperature

Machine-Learning Assisted Laser Powder Bed Fusion Process Optimization for AlSi10mg: New Microstructure Description Indices and Fracture Mechanisms

Additive Manufacturing of AlSi10Mg and Ti6Al4V Lightweight Alloys via Laser Powder Bed Fusion: A Review of Heat Treatments Effects