Abstract:AlSi10Mg is a hypoeutectic alloy that has remarkable characteristics and implemented in diverse areas. Most of the AlSi10Mg parts are fabricated via traditional processes. The AlSi10Mg parts made by these processes have coarser microstructure, reduced mechanical behaviors, and minimum lifespan. This study is aimed at manufacturing the AlSi10Mg parts by Laser Powder Bed Fusion (LPBF) process followed by analyzing their mechanical properties. The microstructure evolution was examined from the micrographs of Optical Microscope (OM), Field Emission Scanning Electron Microscope (FESEM), Electron Backscatter Diffraction (EBSD), and Transmission Electron Microscope (TEM). Tafel, Nyquist, Bode and surface plots were used to determine the corrosion resistance and surface roughness at different intervals. FESEM micrographs revealed the existence of bimodal equiaxed α-Al grains containing Si phase as their grain boundaries. After solidification, the secondary precipitates (Mg 2 Si) were segregated in the printed sample which accounts for enhancing the mechanical characteristics. More grain growth and textures were noticed along the building direction of the sample and this direction exhibits higher hardness compared with the scanning direction. Further, TEM analysis confirmed that the formed microstructure is rich in equiaxed α-Al with Si eutectics. Corroded X-ray Diffraction (XRD) plot showed that the maximum intensity of MgAl 2 O 4 is observed at 25 h immersion test sample. Among the various samples, 25 h LPBF sample provides significant resistance toward corrosion based on the values of current density, polarization resistance and average surface roughness. This is due to the formation of stable passive film on its surface thereby providing better anti-corrosion characteristics.

Influence of eutectic-Si in as-cast and fibrous-eutectic-Si in LPBF-processed AlSi10Mg alloys on wear and corrosion behaviors treated with direct aging route

Wear Behavior of AlSi10Mg Alloy Produced by Laser‐Based Powder Bed Fusion and Gravity Casting

Fretting wear behavior on LPBF processed AlSi10Mg alloy for different heat treatment conditions

Effect of α-Al and Si Precipitates on Microstructural Evaluation and Corrosion Behavior of Laser Powder Bed Fusion Printed AlSi10Mg Plates in Seawater Environment

Study on Microstructure, Mechanical Properties and Erosion Characteristics of Al-Si Alloy Manufactured by Continuous Casting Direct Rolling Process

Effect of build direction and surface finish on wear behavior of AlSi10Mg alloy casted by laser powder bed fusion

The Effect of Heat Treatment on the Mechanical Properties and Oxidation Resistance of AlSi10Mg Alloy

Effect of direct aging treatment on microstructure, mechanical and corrosion properties of a Si-Zr-Er modified Al-Zn-Mg-Cu alloy prepared by selective laser melting technology

Comparative analysis on high temperature tribological behaviour of additive manufactured and cast AlSi10Mg alloy

Comparative tribological studies of additive manufactured as-built and chemically polished AlSi10Mg alloy surfaces

Impact of Aging Time on the Morphological, Mechanical, and Tribological Behavior of Al-6.6Si-0.2Mg-0.2La Hypoeutectic Alloy

Effect of Heat Treatment on Tribological Properties of SiCp/Al–Mg–Mn–Cu Aluminum Matrix Composites

Effect of Deep Cryogenic Aging Treatment on Microstructure and Mechanical Properties of Selective Laser-Melted AlSi10Mg Alloy

Influence of ageing temperature on the tribological characteristics of LM25/Al2O3/SiC hybrid metal matrix composite for lightweight applications

Microstructure and Wear Resistance of Laser-Treated and Slow Cooled AlSi10Mg-(x)Ni Alloys

Solutionizing Temperature Effect on the Dry Sliding Wear Performance of Al-7Si-0.3Mg-3Ni Hypoeutectic Alloy

Influence of Microstructural Characteristics on the Mechanical and Wear Behavior of Wire Arc Additive Manufactured and Cast Eutectic Al-Si Alloy

Aging temperature effects on microstructure and mechanical properties for additively manufactured AlSi10Mg

Effect of Ageing Temperature on the Hardness, Microstructural and Dry Sliding Wear Performance of the Functionally Graded A356 Alloy

Effect of heat treatment on corrosion and ultrasonic cavitation erosion resistance of AlSi10MnMg alloy

Exploring Microstructure, Wear Resistance, and Electrochemical Properties of AlSi10Mg Alloy Fabricated Using Spark Plasma Sintering