Abstract:Wire arc additive manufacturing (WAAM) is a direct energy deposition process majorly used to fabricate large and medium-sized components. However, the process encounters defects, such as anisotropic microstructure and mechanical properties, residual stresses, excessive oxidation , and geometrical irregularities. Hence, efforts have been made to address the issues by optimizing the process parameters and incorporating in situ and post-process treatment to improve mechanical properties. In line with this, the present work deals with statistical-based process parameter optimization based on a multicriteria approach. The responses were quantified, statistically analyzed, and correlated with the process parameters. Travel speed exhibited a minor effect on all responses, while the current and wire feed speed significantly affected the responses. The percentage porosity was more sensitive to welding current than the other parameters. The maximum ultimate tensile strength (UTS) of 193.73 ± 3.93 MPa and yield strength (YS) of 108.09 ± 12.28 were displayed by Wall 2. YS and UTS showed marginal variation in vertical and horizontal directions, while % elongation showed significant variation. The desirability Wall (DW) exhibits better-forming quality due to the minimization of the contact angle, and fibrous silicon was observed between the layers. In contrast, it appears to be fragmented silicon at the interfacial region due to remelting and breakdown of Si. However, there were a few limitations to the DW wall's mechanical properties due to coarser dendrites and bulk eutectic at the interface. The average grain size of the bottom and top region for the optimized parameter is 111.156 μm and 173.66 μm, respectively. The observed texture components in the top region include C{001} 〈110〉, A2* (111) [11 2 ̄ ], A (1 1 ̄ 1) [110], and B (1 1 ̄ 2) [110], exhibiting a maximum texture intensity of 10.414. In the bottom region, the identified texture components are B ̄ ( 1 ̄ 1 2 ̄ ) [ 1 ̄1 ̄ 0], B (1 1 ̄ 2) [110], A (1 1 ̄ 1) [110], C{001} with a maximum texture intensity of 10.110.

Influence of Microstructural Characteristics on the Mechanical and Wear Behavior of Wire Arc Additive Manufactured and Cast Eutectic Al-Si Alloy

Enhanced High-Temperature Strength and Ductility of Wire Arc Additive Manufactured Al-Ce-Mg Alloys with Fine Α-Al/al11ce3 Eutectics

Surface Characteristics, Microstructural, and Tribological Behavior of Wire Arc Additive Manufactured Aluminum-5356 Alloy

Influence of Arc Length Correction on Friction and Wear Characteristics of Wire-Arc Additive Manufactured AA 5356 Alloy

Microstructure evolution and mechanical properties of the wire plus arc additive manufacturing Al-Cu alloy

Microstructure evolution and mechanical properties of the wire + arc additive manufacturing Al-Cu alloy

Experimental investigation on wear resistance and corrosion behavior of nickel-aluminum bronze alloy fabricated by wire-arc additive manufacturing

Comparative Study on Wire-Arc Additive Manufacturing and Conventional Casting of Al–Si Alloys: Porosity, Microstructure and Mechanical Property

Microstructure, Hardness, and Electrical Resistivity of Al-Cu alloy fabricated via Wire Arc Additive Manufacturing

Microstructure, Mechanical Properties and Tribological Behavior of Wire Electron Beam Additive Manufactured Eutectic Al–12Si Alloy

Microstructural evolution and mechanical characterization of wire arc additively manufactured 2Cr13 thin-wall part

Wire arc additive manufacturing of ER-4043 aluminum alloy: evaluation of bead profile, microstructure, and wear behavior

Effect of Wire Composition on Microstructure and Properties of Wire and Arc Additive Manufactured ZAlCu5MnCdVA Aluminum Alloy

Dry Sliding and Slurry Abrasion Behaviour of Wire Arc Additive Manufacturing - Cold Metal Transfer (WAAM-CMT) Cladded Inconel 625 on EN8 Steel

Wire Arc Additive Manufacturing of Al-Cu Alloy-Grain Refinement, Strengthening and Thermal Simulation

Microstructural and Defect Evolution during WAAM Resulting in Mechanical Property Differences for AA5356 Component

Microstructures and Mechanical Properties of Wire Arc Additive Manufactured 5183-Al: Influences of Deposition Dimensions

Microstructural Evolution and Mechanical Properties of 2219 Aluminum Alloy Deposited by Wire and Arc Additive Manufacturing

Multiscale modelling of microstructure, micro-segregation, and local mechanical properties of Al-Cu alloys in wire and arc additive manufacturing

Wear Behavior Assessment of New Wire-Arc Additively Manufactured Surfaces on AA6061 and AA5086 Alloys through Multi-Walled Carbon Nanotubes and Ni Particles Inducement

Investigating the microstructure and mechanical behavior of optimized eutectic Al Si alloy developed by direct energy deposition