Abstract:Wire arc additive manufacturing (WAAM) has advantages in fabricating large-size high-strength aluminum due to unconcentrated heat sources and lower cooling rates. Successful practices in depositing high-strength 2000 series alloys have been reported extensively in recent years. However, research on the WAAM of ultra-highstrength 7000 series Al-Zn-Mg-Cu alloys is still in the feasibility verification stage. This study aims to clarify the complex relationship between microstructures and interlayer temperatures during WAAM in a high alloyed quaternary Al-Zn-Mg-Cu alloy. Single-pass multi-layered components were fabricated with interlayer temperatures of 100 degrees C, 200 degrees C, and 300 degrees C for microstructure characterization. A validated numerical model was used to simulate the thermal process and provide clues for mechanism analysis. Results show that higher interlayer temperatures lead to the non-uniform orientation of twin dendrites, refined grains, and increased high angle grain boundaries (HAGBs). But its effects on the phase type and chemical composition of second phases and precipitates are very limited. Rising interlayer temperatures help to accelerate the dynamic precipitation progress. In the thermal cycles of the specimens included in this work, the contribution of arc heat is vital to drive the dynamic precipitation process. In contrast, the contribution of interlayer temperature is very limited in general. However, higher interlayer temperatures do contribute more to driving the dynamic precipitation process. The non-uniform distribution of hardness was observed along the height direction of the fabricated specimens, where the evolution of hardness agrees well with the progress of dynamic precipitation.

Multiscale modelling of microstructure, micro-segregation, and local mechanical properties of Al-Cu alloys in wire and arc additive manufacturing

Modelling and Experimental Observation of the Deposition Geometry and Microstructure Evolution of Aluminum Alloy Fabricated by Wire-Arc Additive Manufacturing

Enhanced High-Temperature Strength and Ductility of Wire Arc Additive Manufactured Al-Ce-Mg Alloys with Fine Α-Al/al11ce3 Eutectics

Microstructure and Solute Concentration Analysis of Epitaxial Growth During Wire and Arc Additive Manufacturing of Aluminum Alloy

Microstructures and Mechanical Properties of Wire Arc Additive Manufactured 5183-Al: Influences of Deposition Dimensions

Microstructure evolution and mechanical properties of the wire plus arc additive manufacturing Al-Cu alloy

Microstructure evolution and mechanical properties of the wire + arc additive manufacturing Al-Cu alloy

Microstructure characteristics under varying solidification parameters in different zones during CMT arc additive manufacturing process of 2319 aluminum alloy

Wire arc additive manufacturing of Al-Zn-Mg-Cu alloy: Microstructures and mechanical properties

Impact of Process Parameters on Forming Quality and Deposition Efficiency of Unsupported Rods in Wire Arc Additive Manufacturing

Effects of Deposition Paramaters on the Microstructure Evolution of Wire Arc Additive Manufactured Al–Zn–Mg–Cu Alloy

Numerical Simulation of Arc Characteristics and Multi-Layer Deposition of Cu Alloys Fabricated by Wire Arc Additive Manufacturing

Control of macro-/microstructure and mechanical properties of a wire-arc additive manufactured aluminum alloy

Wire Arc Additive Manufacturing of Inconel 718: Constitutive Modelling and Its Microstructure Basis

Inhomogeneity and anisotropy of Al-Zn-Mg-Cu alloy manufactured by wire arc additive manufacturing: microstructure, mechanical properties, stress corrosion cracking susceptibility

Effects of Location on the Microstructure and Mechanical Properties of Cu-8Al-2Ni-2Fe-2Mn Alloy Produced Through Wire Arc Additive Manufacturing

Multi-physical modelling of alloy element transportation in wire arc additive manufacturing of a γ -TiAl alloy

Microstructural development during wire arc additive manufacturing of copper-based components

Effects of Interlayer Temperature on the Microstructures of Wire Arc Additive Manufactured Al-Zn-Mg-Cu Alloy: Insights into Texture Responses and Dynamic Precipitation Behaviors

Research progress in wire arc additive manufacturing of aluminum alloys

Multi-layer Deposition Mechanism in Ultra High-Frequency Pulsed Wire Arc Additive Manufacturing (WAAM) of NiTi Shape Memory Alloys