Abstract:Abstract Studies have shown the influence of WAAM process parameters on mechanical properties, bead formation, dimensional accuracy, and microstructure. However, metal transfer modes and their interactions with input variables have not been investigated thoroughly. Therefore, short/spray, pulse and double pulse modes were investigated in this study at different current levels. Bead-on-plate trials were conducted by depositing ER70S-6 wire to investigate bead morphology, dilution, microstructure, and hardness. The study was supported by a detailed statistical approach, including analysis of variance (ANOVA) and regression analysis. Similarly, the combined effects of hatch distance and current were studied on bead formation in multi-layer deposits. Moreover, a thin wall and a cubic structure were deposited to realize the WAAM capability for larger depositions. The microstructures of thin wall and cubic structure were analyzed using optical microscopy (OM) and scanning electron microscopy (SEM). The study concludes that metal transfer modes at various currents significantly influence bead geometry, microstructure and hardness. The microstructure of bead-on-plate trials show fine lamellar structure at low current in all modes. Higher current results in coarse grains with a polygonal and columnar morphology. The hardness shows a decreasing trend as the current increases. The combined effects of current and hatch distance alter bead morphology; however, an optimized combination yields smoother surfaces. The microstructure of thin wall showed a slight anisotropy along the building direction. The presence of small pores was witnessed from OM and SEM images. Similarly, the cubic structure showed a more homogeneous microstructure with much lower porosity. The hardness profile of the thin wall exhibited small fluctuations along the building direction, while that of the cubic structure was more uniform.

Wire Arc Additive Manufacturing of ER-4043 Aluminum Alloy: Effect of Tool Speed on Microstructure, Mechanical Properties and Parameter Optimization

Wire arc additive manufacturing of ER-4043 aluminum alloy: evaluation of bead profile, microstructure, and wear behavior

Impact of Process Parameters on Forming Quality and Deposition Efficiency of Unsupported Rods in Wire Arc Additive Manufacturing

Wire Arc Additive Manufacturing: A Comprehensive Review and Research Directions

Microstructures and Mechanical Properties of Wire Arc Additive Manufactured 5183-Al: Influences of Deposition Dimensions

Multiscale modelling of microstructure, micro-segregation, and local mechanical properties of Al-Cu alloys in wire and arc additive manufacturing

Unveiling the Characteristics of ER70S-6 low Carbon Steel Alloy Produced by wire arc Additive Manufacturing at Different Travel Speeds

Surface Characteristics, Microstructural, and Tribological Behavior of Wire Arc Additive Manufactured Aluminum-5356 Alloy

Influence of travel speed on microstructure and mechanical properties of wire + arc additively manufactured 2219 aluminum alloy

Machinability of gas metal arc based 3D printed Al-Mg 5356 alloy using wire-EDM

Effects of arc current and travel speed on the processing of stainless steel via wire arc additive manufacturing (WAAM) process

Wire Arc Additive Manufactured Radial Thin Wall: Fabrication Strategy, Macroscopic Defect Control, Microstructure, and Mechanical Properties

Modelling and Experimental Observation of the Deposition Geometry and Microstructure Evolution of Aluminum Alloy Fabricated by Wire-Arc Additive Manufacturing

Process and Heat Resources for Wire Arc Additive Manufacturing of Aluminium Alloy ER4043: A Review

Control of macro-/microstructure and mechanical properties of a wire-arc additive manufactured aluminum alloy

Influence of Wire Arc Additive Manufacturing Beads’ Geometry and Building Strategy: Mechanical and Structural Behavior of ER70S-6 Prismatic Blocks

Elucidating the effects of metal transfer modes and investigating the material properties in wire-arc additive manufacturing (WAAM)

Printing High-Strength High-Elongation Al4043 Alloy Using UNS A94043 Welding Wires through Wire Arc Additive Manufacturing

The Effects of Processing Parameters during the Wire Arc Additive Manufacturing of 308L Stainless Steel on the Formation of a Thin-Walled Structure

Wire Arc Additive Manufactured Mild Steel and Austenitic Stainless Steel Components: Microstructure, Mechanical Properties and Residual Stresses

Effect of Travel Speed on the Properties of Al-Mg Aluminum Alloy Fabricated by Wire Arc Additive Manufacturing