Abstract:Additive manufacturing (AM) is becoming increasingly popular since it offers flexibility to produce complex designs with less tooling and minimum material at shorter lead times. Wire arc additive manufacturing (WAAM) is a variant of additive manufacturing which allows economical production of large-scale and high-density parts. The WAAM process has been studied extensively on different steels; however, the influence of process parameters, specifically wire feed speed (WFS), travel speed (TS), and their ratio on bead geometry, microstructure, and mechanical properties, are yet to be studied. The present work aims at closing this gap by using the WAAM process with robotic cold metal transfer (CMT) technology to manufacture high-strength structural steel parts. For that purpose, single-bead welds were produced from HSLA steel by varying WFS between 5 and 10 m/min and the WFS to TS ratio between 10 and 20. Those variations produce heat inputs in the range of 266–619 J/mm. The results have shown that the wire feed speed to travel speed ratio is the major parameter to control the heat input. Increasing heat input increases characteristic bead dimension, whereas it reduces the hardness. In the second part of experiments, two single-bead walls were deposited via the parallel deposition strategy and one multiple-bead wall was produced using the oscillation strategy. The tensile properties were tested along two directions: parallel and perpendicular to deposition directions. For the yield strength and tensile strength, the difference between horizontally and vertically tested specimens was smaller than the standard deviations. On the other hand, the total and uniform elongation values exhibit up to 10% difference in the test direction, indicating anisotropy in ductility. Those tensile properties were attributed to repeated thermal cycles during the WAMM process, which can cause heat transfer in multiple directions. The yield strength of the multiple-bead wall produced via oscillation was lower, whereas its ductility was higher. The tensile properties and hardness differences were found to correlate well with the microstructure.

Microstructural characteristics and tensile properties of ER70S-6 manufactured by Robotic CMT wire-and-arc additive manufacturing

Unveiling the Characteristics of ER70S-6 low Carbon Steel Alloy Produced by wire arc Additive Manufacturing at Different Travel Speeds

Microstructural and mechanical properties analysis of SS 316L structure fabricated using CMT-wire arc additive manufacturing

Microstructure and mechanical properties of the wire arc additively manufactured 316L/ER70S-6 bimetal structure

Mechanical properties of wire arc additive manufactured carbon steel cylindrical component made by gas metal arc welding process

Mechanical, metallurgical, and corrosion investigations on wire arc additively manufactured low carbon steel

Wire arc additive manufacturing of ER-4043 aluminum alloy: evaluation of bead profile, microstructure, and wear behavior

Wire Arc Additive Manufactured Mild Steel and Austenitic Stainless Steel Components: Microstructure, Mechanical Properties and Residual Stresses

Mechanical properties and microstructure characteristics of wire arc additively manufactured high-strength steels

Experimental study of shielding gas concentration on mechanical properties of stainless steel alloy parts using wire and arc additive manufacturing

Selection of Parameters for Optimized WAAM Structures for Civil Engineering Applications

Characterization of a low-alloy steel component produced with wire arc additive manufacturing process using metal-cored wire

Analysis of Favorable Process Conditions for the Manufacturing of Thin-Wall Pieces of Mild Steel Obtained by Wire and Arc Additive Manufacturing (WAAM)

Mechanical properties of wire arc additive manufactured carbon steel cylindrical component made by cold metal transferred arc welding process

Mechanical behavior of austenitic stainless steels produced by wire arc additive manufacturing

Wire Arc Additive Manufactured Radial Thin Wall: Fabrication Strategy, Macroscopic Defect Control, Microstructure, and Mechanical Properties

Wire arc additive manufacturing of high-strength low alloy steels: study of process parameters and their influence on the bead geometry and mechanical characteristics

Experimental characteristics of 316L stainless steel thin wall processed in wire-based arc additive manufacturing process

Microstructural evolution and mechanical characterization of wire arc additively manufactured 2Cr13 thin-wall part

Wire Arc Additive Manufacturing of ER-4043 Aluminum Alloy: Effect of Tool Speed on Microstructure, Mechanical Properties and Parameter Optimization

A review on wire arc additive manufacturing based on cold metal transfer