Abstract:Wire and arc additive manufacturing (WAAM) has emerged as a highly promising technique for manufacturing large-scale steel structural elements. However, the distinct mechanical properties of WAAM steel could potentially lead to different performance of WAAM steel bolted connections compared to the traditional steel bolted connections. This study aims to investigate the material properties of WAAM steel and the structural behaviours of WAAM steel bolted connections, focusing on the effects of print layer orientation and connection plate geometrical dimensions. A total number of 24 WAAM steel coupon specimens with three different print layer orientations and 36 WAAM double-shear bolted connections with two print layer orientations and different geometric dimensions were designed, fabricated and tested under monotonic tension. These specimens were measured using a 3D laser scanner and Digital Image Correlation (DIC) was adopted to measure the structural response during testing. The impact of print layer orientations on WAAM material properties and the effects of WAAM material properties on bolted connections were analysed and discussed. The current design codes for traditional steel bolted connections were evaluated against the test results of WAAM steel bolted connections. The study found that the print layer orientations of WAAM steel plates initiated an anisotropic material property of the coupon specimens, demonstrated by the differences in ultimate tensile strength and strain of specimens with different print layer orientations. Five failure modes, including net section tension, shear-out, bearing, end-splitting, and block shear failure were observed for the bolted connections. The material anisotropy further affects the performance of the bolted connections, though in the same dimensions, 28% of the specimens presented different failure modes due to the different print layer orientations. The effectiveness of current steel design standards was compromised by inaccurate predictions of failure modes due to the distinct end-splitting failure mode and the effects of material anisotropy, though the predictions of the ultimate capacities of the WAAM lap shear specimens were relatively accurate.

Mechanical behavior of austenitic stainless steels produced by wire arc additive manufacturing

Mechanical Properties, Microstructural Characteristics and Heat Treatment Effects of WAAM Stainless-Steel Plate Material

Microstructure and Mechanical Properties of 304L Steel Fabricated by Arc Additive Manufacturing

Improving mechanical strength and isotropy for wire-arc additive manufactured 304L stainless steels via controlling arc heat input

Experimental Study on Wire and Arc Additively Manufactured Steel Double-Shear Bolted Connections

Mechanical properties and microstructure characteristics of wire arc additively manufactured high-strength steels

Experimental Study on Mechanical Properties and Bond Behavior of Wire and Arc Additive Manufacturing Steel Bar

Improve the Manufacturing Efficiency of Steel Bars by Using Hot-Wire Pulse Arc Additive Manufacturing

Structural Behaviour and Design of Wire Arc Additively Manufactured Bolted Connections with Thick Plates

Experimental characteristics of 316L stainless steel thin wall processed in wire-based arc additive manufacturing process

Tensile properties and microstructural features of 304L austenitic stainless steel produced by wire-and-arc additive manufacturing

Wire Arc Additive Manufactured Mild Steel and Austenitic Stainless Steel Components: Microstructure, Mechanical Properties and Residual Stresses

Microstructure and Mechanical Properties of Low-Carbon High-Strength Steel Fabricated by Wire and Arc Additive Manufacturing

Anisotropic Behavior of Super Duplex Stainless Steel Fabricated by Wire Arc Additive Manufacturing

Novel geometrical model and design mechanical parameters for CMT-WAAM stainless steel

Microstructural and mechanical properties analysis of SS 316L structure fabricated using CMT-wire arc additive manufacturing

Multiscale analysis of mechanical behavior of multilayer steel structures fabricated by wire and arc additive manufacturing

Microstructure and Texture of 2205 Duplex Stainless Steel Addi-Tive Parts Fabricated by the Cold Metal Transfer (CMT) Wire and Arc Additive Manufacturing (WAAM)

Experimental study of shielding gas concentration on mechanical properties of stainless steel alloy parts using wire and arc additive manufacturing

Influence of Interlayer Forced Air Cooling on Microstructure and Mechanical Properties of Wire Arc Additively Manufactured 304L Austenitic Stainless Steel

The Fracture Toughness and Fatigue Crack Growth Properties of 18ni 300 Maraging Steel Manufactured by Wire + Arc Additive Manufacturing