Abstract:Wire arc additive manufacturing (WAAM) technology has potential advantages in the production of large-scale aluminum alloy components. However, as-deposited Al–Cu alloys produced by WAAM often suffer from porosity defects and coarse eutectic phases distributed along the grain boundaries, resulting in poor mechanical properties and hindering the applicability of WAAM to prepare aluminum alloy components. Herein, 2219 aluminum alloy was prepared using WAAM assisted by interlayer friction stir processing (FSP). Porosity defects in the as-deposited materials were eliminated, and coarse eutectic phases were broken and dissolved into the α-Al matrix via interlayer FSP, improving the mechanical properties of the components. The specimens processed by WAAM + interlayer FSP were subjected to different thermal cycling at different locations. The top-layer stir zone (SZ) was not affected by thermal cycling during the additive manufacturing process, and mechanical properties in the SZ were superior to those in the middle region. Compared with the as-deposited materials prepared by WAAM, the yield strength (YS) and ultimate tensile strength (UTS) in the middle region along the horizontal direction of the components manufactured by WAAM + interlayer FSP increased from 118 to 143 MPa and from 255 to 277 MPa, respectively. Further, the ultimate fatigue strength increased from 97 to 139 MPa. The YS and UTS along the vertical direction were 140 and 268 MPa, respectively, which are slightly lower than those along the horizontal direction. This is due to the small overlapping between the two adjacent SZs. The partially melted zone (PMZ) between the SZs was not completely eliminated, and the θ phase in the PMZ was mostly distributed along the grain boundaries.

Influence of travel speed on microstructure and mechanical properties of wire + arc additively manufactured 2219 aluminum alloy

Improving mechanical strength and isotropy for wire-arc additive manufactured 304L stainless steels via controlling arc heat input

Effect of Travel Speed on the Properties of Al-Mg Aluminum Alloy Fabricated by Wire Arc Additive Manufacturing

Microstructure evolution and mechanical properties of the wire + arc additive manufacturing Al-Cu alloy

Mechanical properties and precipitation behavior of the heat-treated wire + arc additively manufactured 2219 aluminum alloy

Microstructure Evolution and Performance of AA2024 Alloy Through Wire-Arc Additive Manufacturing Under Different Heat Inputs

Influence of temperature on deformation and damage mechanisms of wire + arc additively manufactured 2219 aluminum alloy

Microstructure and mechanical properties of wire arc additively manufactured 205A high strength aluminum alloy: The comparison of as-deposited and T6 heat-treated samples

Unveiling the Characteristics of ER70S-6 low Carbon Steel Alloy Produced by wire arc Additive Manufacturing at Different Travel Speeds

Microstructure refinement and mechanical properties enhancement of wire-arc additive manufactured 2219 aluminum alloy assisted by interlayer friction stir processing

The structure and mechanical properties of high-strength aluminum alloys fabricated with wire arc additive manufacturing

Multiscale modelling of microstructure, micro-segregation, and local mechanical properties of Al-Cu alloys in wire and arc additive manufacturing

Evolution of microstructure and properties in 2219 aluminum alloy produced by wire arc additive manufacturing assisted by interlayer friction stir processing

Effect of fabrication parameters on the microstructure and mechanical properties of wire arc additive manufactured AZ61 alloy

Comparative Study on Wire-Arc Additive Manufacturing and Conventional Casting of Al–Si Alloys: Porosity, Microstructure and Mechanical Property

Microstructure characteristics under varying solidification parameters in different zones during CMT arc additive manufacturing process of 2319 aluminum alloy

Wire Arc Additive Manufacturing of ER-4043 Aluminum Alloy: Effect of Tool Speed on Microstructure, Mechanical Properties and Parameter Optimization

The heterogeneous band microstructure and mechanical performance in a wire + arc additively manufactured 2219 Al alloy

Minimizing porosity and optimizing microstructure of hot-wire arc additive manufactured Al-Cu-Mg-Ag alloy for strength increment

Microstructure and mechanical properties of wire arc additive manufactured ZL205A alloy

Wire arc additive manufacturing of Al-Zn-Mg-Cu alloy: Microstructures and mechanical properties