Abstract:Wire arc additive manufacturing (WAAM) technology was used to produce samples of a 2.25Cr1Mo0.25V heat-resistant steel. The phase composition, microstructure, and crystal structure of the investigated material in the as-cladded state and postcladding heat-treated (705°C × 1 h) state were analysed by optical emission spectrometry (OES), optical microscopy, scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The properties of the investigated material in the as-cladded state and postcladding heat-treated (705°C × 1 h) state were determined by a microhardness tester, mechanical properties tester, and Charpy impact tester. Through a study of the microstructure and properties, it is found that the investigated material produced by WAAM exhibits good forming quality and excellent metallurgical bonding properties, and no obvious defects are found. The microstructure consists mainly of Bg (granular bainite) and troostite precipitated at the grain boundaries. The results from high-resolution transmission electron microscopy observations show that the crystal structures of the 2.25Cr1Mo0.25V heat-resistant steel samples produced by WAAM in the as-cladded condition have many defects, such as dislocations and martensite-austenite (M-A) constituents, and their grain edges are sharp. There is a dramatic decrease in the dislocations in the 2.25Cr1Mo0.25V heat-resistant steel samples produced by the WAAM condition after the postcladding heat treatment (705°C × 1 h), and the grains become smooth. The distribution of the microhardness in the longitudinal and transverse cross sections of the samples is very uniform. The average longitudinal and transverse microhardness of the samples in the as-cladded state is 310 HV 0.5 and 324 HV 0.5 , respectively. The average longitudinal and transverse microhardness of the samples after post-cladding heat treatment is 227 HV 0.5 and 229 HV 0.5 , respectively. The yield strength of the samples without a postcladding heat treatment is 743 MPa, the tensile strength is 951 MPa, the elongation is 10%, and the Charpy impact value at -20°C is 15 J. After the postcladding heat treatment, the yield strength, tensile strength, elongation, and Charpy impact value of the samples are 611 MPa, 704 MPa, 14.5%, and 70 J, respectively.

Dry Sliding and Slurry Abrasion Behaviour of Wire Arc Additive Manufacturing - Cold Metal Transfer (WAAM-CMT) Cladded Inconel 625 on EN8 Steel

CMT-based wire arc additive manufacturing of Inconel 625 alloy

Experimental investigation of CMT discontinuous wire arc additive manufacturing of Inconel 625

Influence of droplet transfer behaviour on the microstructure, mechanical properties and corrosion resistance of wire arc additively manufactured Inconel (IN) 625 components

Location-dependent microstructure analysis and mechanical behavior of inconel 625 using Cold Metal Transfer(CMT) based wire and arc additive manufacturing

Slurry abrasion behaviour of ERNiCrMo-3 cladding on EN8 steel developed by WAAM

Influence of Microstructural Characteristics on the Mechanical and Wear Behavior of Wire Arc Additive Manufactured and Cast Eutectic Al-Si Alloy

Investigation of Surface Residual Stress, Mechanical Properties, and Metallurgical Characterization of Inconel 625 Multilayer Thin-Wall Component Using Cold Metal Transfer Technique

Cold Metal Transfer-Based Wire Arc Additively Manufactured Austenitic Stainless Steel/Inconel 625/Superduplex Stainless Steel Wall: Microstructural, Corrosion Properties, and Impact Toughness Evaluation

Technology Development for Producing Inconel 625 in Aerospace Application Using Wire Arc Additive Manufacturing Process

Microstructure and Mechanical Properties of Thick‐Walled Inconel 625 Alloy Manufactured by Wire Arc Additive Manufacture with Different Torch Paths

On the Effect of Heat Input and Interpass Temperature on the Performance of Inconel 625 Alloy Deposited Using Wire Arc Additive Manufacturing–Cold Metal Transfer Process

High-efficiency fabrication of Inconel 625 coating for AISI 1045 carbon steel through laser cladding with hot wire: Microstructure and wear resistance

Influence of Interlayer Temperature on Microstructure and Mechanical Properties of Additively Manufactured Inconel 625

Wear Behavior Assessment of New Wire-Arc Additively Manufactured Surfaces on AA6061 and AA5086 Alloys through Multi-Walled Carbon Nanotubes and Ni Particles Inducement

Microstructure and high-temperature wear behaviour of Inconel 625 multi-layer cladding prepared on H13 mould steel by a hybrid additive manufacturing method

Microstructural Features and Mechanical Integrity of Wire Arc Additive Manufactured SS321/Inconel 625 Functionally Gradient Material

A Study on Microstructure and Mechanical Properties of Inconel 718 Superalloy Fabricated by Novel CMT-WAAM Process

Surface Characteristics, Microstructural, and Tribological Behavior of Wire Arc Additive Manufactured Aluminum-5356 Alloy

Effect of welding parameters on bead characteristics and mechanical properties of wire and arc additive manufactured inconel 718

Microstructure and Properties of a 2.25Cr1Mo0.25V Heat-Resistant Steel Produced by Wire Arc Additive Manufacturing